See Product Specifications on page 2 for your dust collector maximum static pressure. NOTE: To determine if you have met the Static Pressure Requirement when using a Dust Collection System, identify the branch of the system with the highest static pressure requirement first, If you run your Dust Collection System with more than one blast gate open, add the static pressure from all branches that are open to determine the total static pressure requirements, Static Pressure Requirement Chart Size o

(no _oad R.P.M.) ST COLL Mode_ No. 152.213361 C CAUTION: FOR YOUR OWN SAFETY; Read and follow all of the Safety and Operating instructions before Operating this Dust Collector. Customer Helpline 1-800-897-7709 Please have your Model No. and Sedal No. available. Sears, Roebuck and Co., Hoffman Estates, JL (}0179 U.S.A. Part No. OR92136 Revision A Espa5olpg. 21 SECTmON PAGE Warranty ..................................................................................... 2 Product Specifications .....

A B B DE 1, Turn base (A) right side up, Align the mounting hobs at the base of blower and motor assembly (B) with six pre-drilled hobs (C) in base and fasten with six 5/16=18 x 5/8" hex head screws (D) and 5/16" lock washer (E), See figure 8, Fig. 9 G 2, 3, 11 Assemble drum support (F) to the two threaded hobs in the corner of base with two 5/16=18 x 5/8" hex head screws and 5/16" lock washer (G), NOTE: Do not completely tighten hardware at this time, See figure 9, Assemble the remaining drum s

Together, the two gear sections create a large volume flow which produces rapid cylinder movement under low load conditions. Above unloading pressure, a pilot pressure line(which simulates actual pressure at the cylinder) activates the unloading valve, which causes the flow to bypass the large gear section and return to the pump inlet area. The small gear section is now operating alone, and will generate the higher pressure necessary for the actual log splitting operation. The original factory

-Route the hose as shown in figure 11. Place the metal pressure tube in position on the fitting on top of control valve. Secure with the compression nut on the pressure tube, using an adjustable wrench. Make certain the metal pressure tube is positioned so that the pressure hose is above the slide plate as shown. FINAL ASSEMBLY • Make certain all nuts, bolts and hose clamps are tightened securely. • Before operating the log splitter, make certain to follow the “Initial Preparation” instructio

247.346250 Caution: Read and Follow All Safety Rules and Instructions Before Operating This Equipment CRAFTSMAN® 5.0 HORSEPOWER 25.5 TON HYDRAULIC LOG SPLITTER Assembly Operation Customer Responsibilities Service and Adjustment Repair Parts SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A. IMPORTANT SAFETY RULES A THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL I

• Safety • Assembly • Operation • Service • Maintenance • Espa5ol Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A. Printed in U.S.A. 770-10032A (8/99) Content Page Warranty Information......................................... 2 Safe Operation Practices................................... 3 Accessories ....................................................... 6 Assembly ........................................................... 7 Operation ..................................................

WARNING: There is a danger of static electricity building up in the dust collector system and causing a flash explosion or fire. To prevent static electricity buildup, install grounding kit. • A grounding kit is included and must be installed in the shop dust collector system to protect against electrostatic discharge. The grounding kit is more easily installed as the individual sections for each machine are assembled. LAYOUT SYSTEM AT SELECTED SITE Temporarily assemble the pieces together as de

Figure 7 -Attaching Inlet ATTACH HOSE Refer to Figure 8. Hose needs to be attached to the inlet using hose clamp. To attach hose: • Slide hose clamp onto one end of hose. Loosen clamp screw if required to slide hose clamp onto hose. • Position the hose clamp wires on the hose grooves. • Slide hose with clamp onto inlet. • Tighten hose clamp screw to secure hose with inlet. • Slide other hose clamp onto the opposite hose end. This end will be connected to the dust producing machine Figure 8 -Atta

CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacem