Votes - 2, Average rating: 3.5 ( )

Manafacture: Citizen File size: 604.48 kb File name: Language of manual:

This data remains stored even after the printer power is off. For the registration method, refer to Command Reference Manual in separate document. To acquire the Command Reference Manual, contact your Citizen Systems dealer. . Memory switch Setting of various kinds of functions can be stored in nonvolatile memory. The functions are valid even if the printer power is turned off. — 14 — 3. PREPARATION 3.1 Connecting the AC Power Cord 1. Turn off the printer power switch. 2. For AC power type (with built-in power supply), connect the AC power cord to the AC inlet at the back of the printer and plug the AC power cord into the wall outlet. AC inlet AC power cord Cable connector Power connector Flat side AC power typeDC power supply type (built-in power supply) CAUTION! ¦ When disconnecting a cable, DO NOT pull out by the cable. Always hold the plug. ¦ Always keep the printer away from other noise generating equipment. ¦ DO NOT pull the AC power cord. Otherwise fire, electric shock, or power disconnection may result. ¦ If lightning is approaching, unplug the AC power cord from the wall outlet. Otherwise fire or electric shock may result. ¦ Keep the power cord away from heat generating appliances. Otherwise the shield of power cord may be fused resulting in a fire or electric shock. ¦ If the printer will not be used for a long time, leave it disconnected from its supply outlet. ¦ Avoid locating the AC power cord in places which may cause tripping or falling. — 15 — 3.2 Connecting Interface Cables 3.2 Connecting Interface Cables Confirm that the power switch is OFF and connect the interface cable. Orient the interface cable terminal correctly and insert it into the interface connector. USB connector Parallel Interface USB Interface Serial Interface CAUTION! ¦ When disconnecting the cable, always hold the connector. ¦ Be careful not to insert the USB interface cable into the cash drawer kick-out connector. For serial interface cable, use the one with the following connection. 25-pin - 25-pin cable 9-pin - 25-pin cable PC Printer PC Printer Signal Pin Pin Signal FG 1 1 FG TXD 2 2 TXD RXD 3 3 RXD CTS 5 4 RTS DSR 6 6 DSR SG 7 7 SG DTR 20 20 DTR Signal Pin Pin Signal RXD 2 2 TXD TXD 3 3 RXD DTR 4 4 RTS SG 5 6 DSR DSR 6 7 SG CTS 8 20 DTR CAUTION! Avoid locating the interface cable in places which may cause tripping or falling. — 16 — 3.3 Connecting the Cash Drawer 3.3 Connecting the Cash Drawer 1. Confirm that the power switch is OFF. 2. Confirm the top and bottom of the cash drawer cable connector and insert it into the cash drawer kick-out connector at the back of the printer. 3. Screw the cash drawer's ground wire to the body of the printer. Cash drawer cable connector Cash drawer kick-out connector CAUTION! DO NOT connect any other device than the specified cash drawer to the cash drawer kick-out connector. (Also DO NOT connect a telephone line.) (1) Connector Pin Configuration (2) Electrical characteristics 1) Driving voltage: 24 VDC No. Signal Function 6 1 1 FG Frame Ground 2 DRAWER 1 Drawer 1 drive signal 3 DRSW Drawer switch input 4 VDR Drawer drive power supply 5 DRAWER 2 Drawer 2 drive signal 6 GND Common ground on circuits Connector used: TM5RJ3-66 (Hirose) or equivalent Applicable connector: TM3P-66P (Hirose) or equivalent 2) Driving current: Approx. 1A max. (shall not exceed 510 ms.) 3) DRSW signal: Signal levels: “L” = 0 to 0.5 V, “H” = 3 to 5 V (3) (4) DRSW signal DRSW signal status can be tested with the DLE+EOT, GS+a, or GS+r command or at pin 34 on the parallel interface port. Drive Circuit (printer side) 1 2 5V VDR 3 4 5 6 VDR CAUTION! ¦ No output is produced while printing. ¦ The cash drawers 1 and 2 cannot be driven simultaneously. ¦ A solenoid used for the cash drawer should be of 24 . or more. The output current should be kept at 1A or less; otherwise, breakdown or burning could occur. — 17 — 3.4 Installing the Printer 3.4 Installing the Printer The printer can be installed horizontally, vertically, and on the wall. At the time of shipment, the printer is set for horizontal installation. To install the printer vertically or on the wall, the following adjustments are required. 1. Adjustment of paper near-end sensor position (See section 3.7) 2. Anti-slip rubber feet (for vertical setting) 3. Optional wall-mounting kit (for wall-mounting) Vertical position CAUTION! ¦ When used in vertical position, the printer ejects paper not to fall naturally even with full cutting. Be careful in using the printer built in equipment, etc. ¦ Ensure that the wall on which the printer is mounted has enough strength before installation. ¦ When using in horizontal setting, avoid cutting full. Otherwise, the cut paper may drop into the cutter and may result in double cutting and narrow pieces of paper. This may cause paper jam. 3.5 Partition for Paper Roll At the time of shipment, this partition is not installed. 1. Confirm that the power switch is OFF. 80mm 82.5mm58mm Scales> Partition> CAUTION! When using 112 paper rol...

Download now

Please, enter two numbers from picture: