Votes - 2, Average rating: 3.5 ( )

Manafacture: Citizen File size: 604.48 kb File name: Language of manual:

* Utility water pipes • Plastic water pipes should not be used for grounding. (Those approved by a Waterworks Department may be used.) ¦ Before connecting or disconnecting the grounding lead to or from the printer, always unplug it from supply outlet. — 4 — PRECAUTIONS IN HANDLING THE PRINTER WARNING Please observe the following precautions for power source and power cord: ¦ Do not plug or unplug the power cord with a wet hand. ¦ Use the printer only at the specified supply voltage and frequency. ¦ Check to make sure that the supply outlet from which the printer is powered has a sufficient capacity. ¦ Do not supply the printer from a power strip or current tap shared with other appliances. ¦ Do not plug the power cord into a supply outlet with dust or debris left on its plug. ¦ Do not use a deformed or damaged power cord. ¦ Do not move the printer while the printer power is on. • Neglecting to handle properly may result in printer failure, emission of smoke, fire, or electric shock. • An overload may cause the power cord to overheat or fire or the circuit breaker to trip. ¦ Do not allow anything to rest on the power cord. Do not place the printer where the power cord will be trampled on. ¦ Do not use or carry the printer with its power cord bent, twisted, or pulled. ¦ Do not attempt to modify the power cord unnecessarily. ¦ Do not lay the power cord in the neighbor of a heating device. • Neglecting these cautions may cause wires or insulation to break, which could result in leakage, electric shock, or printer failure. If the power cord sustains damage, contact your Citizen Systems dealer. ¦ Do not leave things around the supply outlet. ¦ Supply power to the printer from a convenient wall outlet, readily accessible in an emergency. • The printer may not be immediately shut down in an emergency. ¦ Insert the power plug fully into the outlet. ¦ If the printer will not be used for a long time, leave it disconnected from its supply outlet. ¦ Hold the plug and connector when plugging or unplugging the power cord or signal cable after turning off the printer and the appliance connected to it. — 5 — CAUTION Caution label is attached on the position shown in the following figure. Carefully read the precautions in handling before using the printer. THESE LABELS INDICATE THE RISK OF ANY INJURY DUE TO "HIGH TEMPERATURE" OF THE PRINT HEAD AND "SAWTOOTHED EDGE" OF THE MANUAL CUTTER. ¦ Do not transport this printer with the paper roll inside. •Printer failure or breakage may occur. To prevent possible malfunction or failure observe the following. ¦ Avoid operating the printer without paper properly loaded. ¦ Avoid the use of paper not complying with specifications. •May result in poor print quality. ¦ Avoid using torn pieces of paper or spliced with plastic adhesive tapes. ¦ Avoid forcibly pulling already loaded paper by hand. ¦ Avoid wedging the paper into the printer. •May jam paper. To release, refer to “Removing Jammed Paper” in this manual. ¦ Avoid using a sharp pointed device to operate panel keys. ¦ Be sure to firmly insert the cable plug into its mating socket. •A cross connection may damage the printer’s internal electronics or the host system’s hardware. ¦ Only use the printer with devices that have designated solenoid specifications for the cash drawer interface connector. • Neglecting this caution may result in malfunction or failure. — 6 — CAUTION To prevent injury and printer failures from worsening, observe the following: ¦ Do not touch the printing surface of the thermal head. ¦ Do not touch any of the moving parts (e.g., paper cutter, gears, active electrical parts) while the printer is working. ¦ In case of trouble do not attempt to repair the printer. Ask Citizen Systems service for repair. ¦ Be careful that the printer cover does not entrap your hands or fingers. ¦ Be careful with sharp edges on the printer. Do not allow them to injure you or damage property. •May result in electric shock, burn, or injury. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. DAILY MAINTENANCE Observe the following precautions for daily maintenance. ¦ When cleaning the printer, always turn it off and unplug it from the supply outlet. ¦ Use a soft, dry cloth for cleaning the surface of the printer case. ¦ For severe stains, use a soft cloth slightly dampened with water. ¦ Never use organic cleaning solvent such as alcohol, paint thinner, trichloroethylene, benzene, or ketone. Never use a chemically processed cleaning cloth. ¦ To remove paper dust, use a soft brush. CAUTION • The thermal head is at a dangerously high temperature immediately after printing. Allow it to cool off before launching maintenance work. — 7 — THE TABLE OF CONTENTS 1. GENERAL OUTLINE....................................................................9 1.1 Features .............................................................................

Download now

Please, enter two numbers from picture: