Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 6   File size: 1 mb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

For modEls mAnUFACtUrEd sinCE 02/10 #Cr12612 printEd in ChinA This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installat

downloaded: 4   File size: 912 kb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

#JM9879 PRINTED IN CHINA SAFETY For Your Own Safety Read Instruction Manual Before Operating This EquipmentThe purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident preventio

downloaded: 4   File size: 2 mb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

The speed of the ratchet is adjusted by handle paddle position, but the torque is not changed. Model H8208 50-Piece Air Tool Set -5- Impact Wrench Your new single hammer V2" drive impact wrench (Figure 1) will generate up to 230 ft/lbs. of torque. Only use thick-walled impact sockets with this air tool. The common thin-walled chrome sockets may explode if used as impact sockets causing serious injury. At the end of the handle you can adjust the torque setting by pushing the knob in and tur

downloaded: 6   File size: 670 kb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

Touching red and black terminal clamps together will cause a short and may cause an explosion or fire. Never touch red and black terminal clamps together! Tire Inflater The air nozzle is tucked inside the storage compartment that is located near the black terminal clamp. If you are filling a tire at night, and you are on the side of the road near oncoming traffic, use the hazard lights to increase your personal safety. To use the tire inflater: 1. Remove the cover to the storage compartment, and

downloaded: 2   File size: 246 kb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

AIR TOOL KIT Using the Spray Gun 1. Attach the paint reservoir onto the spray gun and attach the air hose. 2. Adjust the air pressure regulator on the compressor to 30 PSI. 3. Identify the spray gun controls in Figure 1 and adjust in the following order: A. Fluid Control—Adjusts how far back the trigger can be pulled, affecting the volume of finish released. B. Pattern Control—Variably adjusts the spray pattern from round to a wide fan. C. Nozzle Control—Adjusts the spray pattern from ver

downloaded: 6   File size: 1 mb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

H4519 3 HP Air Compressor -15 TROUBLESHOOTING PROBLEM CAUSE ACTION Pump motor 1. Low voltage. 1. Check power line for proper voltage. will not start. 2. Open circuit in motor, switch or cord. 3. Tank already pressurized. 4. Thermal overload switch. 2. Inspect all lead connections on motor, switch and cord for loose or open connections. 3. Motor will not start if tank pressure is too high. 4. Thermal overload switch has tripped, wait for motor to cool, then reset switch by pressing red button. Pu

downloaded: 11   File size: 1 mb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

(Most air tools will have an air requirement stated in terms of a specific CFM at a specific pressure.) 2. The compressor should put out a higher CFM than the tool requires. If you are connecting multiple tools that will be used simultaneously, then the CFM for each tool should be added together and compared to the compressor output value. 3. Connect the tool, using a good quality air line with an adequate length to reach from the compressor to the point of use. Note—Quick-connect couplers, show

downloaded: 4   File size: 1 mb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

PRINTED IN CHINA ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE. WARNING Some dust created by power sanding, sawing, grinding

downloaded: 9   File size: 1 mb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

Wear approved hearing protection while operating this machine to minimize this risk! When determining where to set up the air compressor in the shop or when taking the air compressor to a job site, the most important consideration is access to an adequate and properly fused power supply. Refer to Circuit Requirements for the needs of your particular compressor. Also, make sure the compressor is not operating in an environment where there are explosives, flammable or caustic fumes or gases. A cle

downloaded: 9   File size: 770 kb   Manafacture: Grizzly  
Category: Water and Air Pumps
@name

This accessory and many like it can be found in the Grizzly Catalog. Figure 10. Quick connect couplers. Make certain the air hose will not be placed in a position where it can become constricted or cut by a sharp object. Note— Running over a hose with heavy vehicles may not cause an immediate leak, but it will shorten the life of the hose. H3372 3 HP Air Compressor Consideration should also be given to the type of usage. A nailer or staple gun uses air in short bursts and it is easier for the co





Category