Max flow using varibable speed drive, compressors operating at 80 Hz. max speed. 2. Standard test conditions: 60° F suction gas, 60° F ambient, 0.6 SG gas, 14.7 psia = 0 psig 3. Performance data to be used as an estimation guide only and is subject to change without notice 30 2006SSD-75 R4 (10/10) Dual-Compressor Module Technical Support and Service Compressor Module Horsepower Selection Chart Module Model Number: SZO56C1A-EDE-240 Configuration Suction Press (PSIG) Max Flow/HP as a function of d

The common wires on all switches are connected together. All switches are closed unless a fault condition is detected. All safety and protective devices must be installed and used in accordance with applicable codes and regulations. Switches All switch connections are wired to terminal strips in a junction box on the Compressor Module. Switch Status • Low Inlet Gas Pressure Normally Open, closes on pressure rise • High Discharge Gas Pressure Normally Closed, opens on pressure rise • High Tempera

33 A.10 Spill or Leak Procedures.............................................................................................................. 33 A.11 Waste Disposal Methods............................................................................................................. 33 Dual-Compressor Module TABLE OF CONTENTS iii 2006SSD-75 R4 (10/10) FIGURES Figure 1 Compressor Module Components .....................................................................................................

19 2006SSD-75 R4 (10/10) Dual-Compressor Module Maintenance Oil level sight tube 4.3 Checking the Oil Level The proper oil level varies according to the Compressor Module’s operating speed. To check the oil level on the first-stage oil separator level gauge, use the following guidelines based on operating speed. NOTE The oil level indicated on the first-stage oil separator sight tube varies with inlet and discharge pressures as well as operating speed. Check the oil level when the compressor is

Single-Compressor Module Important Safety Information 1 2008SSD-34 (5/11) Important Safety Information This manual contains important instructions for installation, operation and maintenance of your Copeland Scroll® Compressor Module. WARNING The Compressor Module must be installed ONLY in systems that have been designed by qualified engineering personnel. The system must conform to all applicable local and national regulations and safety standards. These instructions are intended to assist in t

Clean or replace. • Insufficient back pressure. Confirm 50-60 psig or higher backpressure when the compressor is running. • No specific cause found. Replace oil separator block assembly, scavenge line and secondary oil separator element. 21 2008SSD-34 (5/11) Single-Compressor Module Maintenance 4.4 Cleaning the Inlet Screen The 30-mesh screen in the inlet block must remain unobstructed for optimal flow rate. If the flow rate is lower than expected even when the Compressor is running properly, th

5. Push the manual control lever to the exhalation phase (to the left). Observe the pressure gauge on the device and adjust the maximum pressure (negative) using the pressure knob to achieve the correct reading on the gauge. 6. Shift the manual control lever to the inhalation phase (push to the right). Adjust the pressure reading by turning the inhale pressure knob to achieve the correct reading on the pressure gauge (clockwise to increase pressure and counterclockwise to decrease pressure). 7.

. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warnings and Cautions . . . . . . . . . . . . . . . . . . 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 4 Controls, Connectors and Visual Indicators . . . . 5 Operating Procedure . . . . . . . . . . . . . . . . . . . . 6 Cleaning and Disinfection . . . . . . . . . . . . . . . . 7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Preventive Maintenance and Troubleshooting Guide 9 Warranty and Service . . .

Your new White-Rodgers thermostat uses solid state microcomputer technology to provide precise time/temperature control. This thermostat offers the flexibility to design heating and cooling programs that fit your needs. Adaptable to most 24 volt residential forced air, multistage or heat pump systems with electric or fossil fuel auxiliary (1F92-371). You will find information about thermostat buttons and display in the component section beginning on page 2. Installation instructions begin on pag

1) Reversing Valve Emergency Heat Relay System Monitor Blower/Fan Dimensions 3.8"H x 6.1"W x 1.1"D Electrical Specifications Rating 20 to 30 VAC, 50/60 Hz or DC 0.05 to 1.2 Amps (load per terminal) 1.5 Amps maximum load (all terminals combined) Standard Systems Heat Pump—2 stage heat, 1 stage cool Single stage heat pump Thermal Specifications Setpoint Temperature Range: 45° to 90°F (7° to 32°C) Rated Differential: 0.6° to 1.6°F with adjustable anticipation Operating Ambient Temperature: 32° to 1