With zone heating, you save 3% on your energy bill for every 1°-thermostat set-back. That’s 15% for every 5°! Your savings can total $312* annually. * Cost savings based on a 5° thermostat set-back. Calculations established on average natural gas/propane heating costs published by U.S. Department of Energy. Gas is still a better value than wood or electricity! $0.37$0.61$0.83$0.94Ideal for any season, new LED flame. Approved for use in any room of the home. Easy operation -Great value --Unparall

causing property damage, personal injury, or Refer to this manual for correct installa loss of life. tion and operational procedures. For as — Do not store or use gasoline or other sistance or additional information con- flammable vapors and liquids in the vicinity of sult a qualified installer, service agency, this or any other appliance. or the gas supplier. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. WARNING: This is an unvented gas• Do not touch any electrical switch;

The cord must have a three-prong, grounding plug and a three-hole receptacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An undersized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet. ATTACHING WOOD BASE TO SOLID FLOOR For attaching base to solid floors (concrete or masonry) Note:Floor anchors and mounting screws are in hardware package. The hardware package i

• As a visual effect - only the flame effect is on, the heater is off. We recommend this mode for warm weather application, when you want the ambiance of a fire, without any heat output. The log set control functions can be accessed in two (2) ways: • Using the control panel buttons, located on the lower right-hand corner of the log set. • Using the multifunction remote control unit. Figure 3 1 2 3 3 2 1 Main Power Button: This button supplies power to all the functions of the log set. The Main

EST, Monday – Friday. 20-10-105 Rev. 6/11 C US INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. IMPORTANT INSTRUCTIONS PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE TABLE OF CONTENTS Safety Information ..................................................................

This will protect your warranty coverage for parts replaced under warranty. PARTS UNDER WARRANTY Contact authorized dealers of this product. If they can’t supply original replacement part(s), call DESA International’s Technical Service Department at 1-800-DESA LOG (1-800-337-2564). When calling DESA International, have ready • your name • your address • model and serial numbers of your fireplace • how fireplace was malfunctioning • type of gas used (propane or natural gas) • purchase date Usuall

Feed flexible gas line into fireplace base area while replacing log base assembly. Make sure the entire flexible gas line is in fireplace base area. Reattach log base assembly to fireplace with screws removed in step 2. CHECKING GAS CONNECTIONS WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once. WARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Cor

The fireplace must set on a metal or wood panel extending the full width and depth of the fireplace. See Accessories on page 33 for mantel kits available for this fireplace. If you are using a separate combustible mantel piece, refer to Figure 7 on page 5 for proper installation height. You can install non-combustible mantels at any height above the fireplace. 20" 34 3/4" 5/8" for drywall facing Must maintain a minimum 1" clearance to combustibles Figure 5 - Framing Clearances for Typical Firepl

Apply a bead of non-hardening mastic around the outside edge of the vent cap. Position the vent cap in the center of the 7 1/2" or 10" hole on the exterior wall with the arrow on the vent cap pointing up. Insure proper clearance of 1" to combustibles is maintained. Attach the vent cap with four wood screws supplied (see Figure 13). Note: Replace the wood screws with appropriate fasteners for stucco, brick, concrete, or other types of siding. WARNING: Do not recess vent termination in to any wall

Check your building codes for any special requirements for locating manual shutoff valve to fireplaces. Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged fireplace valves. We recommend that you install a sediment trap/drip leg in supply line as shown in Figure 35. Locate sediment trap/drip leg where it is within reach for cleaning. Install in piping system between fuel supply and heater. Locate