FEATURES • Attractive white finish • Vertical louvers - disperse heat evenly • Front-mounted, snap action, bimetallic thermostat (Model 112 only) • Heavy-duty, steel sheathed, plate-finned element • Factory-wired for 240 VAC, 1500W • Field-convertible to operate on 120 VAC, 750 or 1500W • Mounts into standard kickspaces beneath cabinets, vanities, counters, stairways, etc. ACCESSORIES (purchase separately) • Model 86W Line-Voltage Thermostat • Model 59W / 59V 60 Minute Timer • Model 6

It is therefore very important to carefully read all the operating instructions, recommendations and warnings prior to installation and use of the appliance. Note in particular the text paragraphs with the danger triangle design, to avoid damages to persons or objects. Keep this instruction booklet in a safe place: this booklet should always accompany the appliance at such time as it is sold or given to other persons for use. Installation and service • Any electrical installation of the cooker h

AEG - putting words into action. Introduction The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear. To connect up the hose, you should first fit the bayonet-mounting flange C on the outlet required (if using the top outlet, fix the flange in place using the screw supplied as s

Check damper to make sure it opens freely. Tape all joints to make them secure and air tight. (Fig. 5) WIRE THE HEATER BLANCO a BLANCO / GRIS WHITE to WHITE BLANCO to BLANCO BLACK to RED & BLUE NEGRO a ROJO y AZUL GROUND TIERRA amortiguador cierre por gravedad. (Fig. 4) 2. Fije el conducto redondo de 10 cm al acople del amortiguador/conducto y saque el tendido de los conductos al exterior a traves de una cubierta de cielo raso o pared. Verifique que el amortiguador se abra libremente. Ponga cint

Protect motor, bulb sockets and wiring from construction dust, drywall spray, paint, etc. by using the plaster shield. Cut it from the carton and follow directions printed on it. (Fig. 7) 2. Finish all ceiling work as necessary. 3. Remove plaster shield and check if bottom of housing is flush with finished ceiling. If not, loosen vertical adjusting screws, reposition housing, and retighten screws. 4. Attach grille by hooking springs onto clips on side of housing. (Fig. 8) 5. Install BR40 or R40-

by using the plaster shield. Cut it from the carton and follow directions printed on it. (Fig. 7) 2. Finish all ceiling work as necessary. 3. Remove plaster shield and check if bottom of housing is flush with finished ceiling. If not, loosen vertical adjusting screws, reposition housing, and retighten screws. 4. Attach grille by hooking springs onto clips on side of housing. (Fig. 8) 5. Install BR40 or R40-size 250W infrared bulb(s). Center grille around bulb(s). FIG. 6 (CONT') ENSAMBLADO FINAL

This is normal and is no cause for concern. DISCONNECT ELECTRIC POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE CLEANING OR SERVICING THIS UNIT. To clean fan assembly: Remove bulb(s). Unhook springs and remove grille. Loosen motor assembly mounting screws and rotate assembly to remove it from housing. Gently vacuum fan, motor and interior of housing. Reverse steps to replace fan assembly. To clean grille assembly: Remove bulb(s). Unhook springs and remove grille. Clean grille with mild soapy wate

Follow the instructions for operating the hood to recirculate air. • When the temperature outdoors becomes more mild (spring), the filter can be removed and the hood converted once again for to extraction. Please consult the assembly instructions for operating the hood in extraction mode. 5 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the us