Do not place unstable or deformed pots on the rings: they Do not place unstable or deformed pots on the rings: theyDo not place unstable or deformed pots on the rings: theyDo not place unstable or deformed pots on the rings: theyDo not place unstable or deformed pots on the rings: theyDo not place unstable or deformed pots on the rings: they could tip over or spill their contents, causing accidents. could tip over or spill their contents, causing accidents.could tip over or spill their contents,

However a detailed visual inspection should reveal evidence of burning around the fault. Ignition System / Gas Ignition Ignition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas Ignition Ignitor does not spark NO NONONONONO YES YESYESYESYESYES Check gas supply at burner Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjus

Please note that proof of purchase is required for in-guarantee service calls. Possible solution If you have checked the above: Allow the appliance to cool for a couple of hours. The appliance should now be working normally. Check that the recommended temperatures and shelf positions are being used. Refer to the main oven section. Check that there is not a problem with your gas supply. You can do this by making sure the other gas appliances such as central heating or gas fires are working. Somet

If only the hotplate burners will not light make sure that the burner parts have been replaced correctly. . If you cannot hear any sparking when you press the ignition button there may be a fault with the electrical supply. First check the socket by trying out another piece of electrical equipment in it. If that works, renew the fuse in the plug. Use a 3 amp fuse. If the fuse 'blows' again there is a fault on the appliance. Do not use a fuse with a rating higher than 3 amps. Do not carry out oth

NOTE: Veuillez lire ces instructions attentivement a fin d’eviter accidents et dommages. NOTA: Por favor, lea este manual de instrucciones atentamente para evitar posibles danos o accidentes. PRODUCT WARRANTY ONE-YEAR LIMITED WARRANTY For one year from the date of purchase, provided this product is operated and maintained in accordance with the instructions attached to or furnished with the product, Fagor America Inc. will replace parts and provide labor to correct defects in materials or workma

The hotplate is operated by touching the corresponding sensors with your finger. Take care to touch only one sensor at a time, otherwise they will not react to the touch. Keep the sensors clean and do not place objects on them. The sensors may misinterpret dirt or objects placed on them. While the cooking surface is off, the indicators for all sensors are also switched off. Starting up Touch the ON/OFF sensor for 3 seconds. The power 0 displays will light up. If no power is selected within five

Note: Do not exert excessive pressure on drum cylinder as this may cause damage. 4. Remove spring clip. Hold socket and pull out old bulb. 5. Hold socket and push in new bulb (DO NOT exceed wattage). Replace spring clip. 6. Repeat steps 3 and 4 for second bulb. 7. Insert bottom edge of removed cylinder half into bottom drum track. Gently squeeze drum cylinder until it's top edge fits into top drum rack. 8. Replace louvered back panel. Replacing Glass 1. Remove top of stove by sliding top toward

Flame motor defective 2. Call a qualified service technician to replace flame motor Dim or poorly visible flame 1. Bulb(s) are burnt out 1. Inspect bulbs and replace if necessary 2. Wiring is loose 2. Inspect wiring for loose connections and repair or replace if necessary Log set and/or ember is not 1. Bulb(s) are burnt out 1. Inspect bulbs and replace if glowing necessary Flame sputters 1. Flame motor is defective 1. Call a qualified service technician to replace flame motor Remote control does

Flame Cylinder Drum Figure 9 - Flame Generation Cylinder Drum 117190-01B 7 CLEANING AND MAINTENANCE Continued CLEANING FRONT PANEL GLASS WARNING: When cleaning unit, the power supply should be disconnected and the unit should be cool. Over time the front glass panel may become dirty or dusty. Dust can be removed by lightly rubbing the glass surface with a clean, lint free cloth or paper towel. To remove fingerprints or other marks, use a damp cloth with a good quality household glass cleaner. Th

This 3rd year warranty provision does not apply to FCI products sold in Canada. Under the terms of this warranty, service must only be provided by an authorized FCI agent. Coverage: Read the Use and Care Manual before using the appliance for the first time! This warranty applies to FCI appliances only for residential use. Our appliances are not intended for commercial use. This warranty is only valid for the original owner and is not transferable. During the warranty time FCI will, at its discre