Votes - 5, Average rating: 4 ( )

Manafacture: GE File size: 897.4 kb File name: 2008a1a1-8e0a-4e89-99a4-e9abcd0e6ac6.pdf Language of manual:

The hotplate is operated by touching the corresponding sensors with your finger. Take care to touch only one sensor at a time, otherwise they will not react to the touch. Keep the sensors clean and do not place objects on them. The sensors may misinterpret dirt or objects placed on them. While the cooking surface is off, the indicators for all sensors are also switched off. Starting up Touch the ON/OFF sensor for 3 seconds. The power 0 displays will light up. If no power is selected within five seconds, the hotplate will automatically switch off and must be switched on again. Power selection - / + Each heater has - / + power sensors. Touching these allows the power to be set in the cooking ranges of 1 to 9. To alter the power while the hotplate is on, touch - / + sensors to obtain the required power level. 10 OPERATING OPERATING Switching off the heat source Choose 0 power for the heat source when you wish to turn off. If the hotplate is hot, H will light up indicating the hotplate is still hot. Residual heat display H When activated but with level 0, the corresponding displays shows 0 and H alternatively. While a hotplate is still hot but switched off, the display will show H. Depending on the power that was used, this display may remain on for up to approximately 30 minutes. Do not touch the hotplate or its surrounding area , white "H" is displayed. There is a risk of burning. Warning! If a power outage occurs while the residual heat display is on, remember that when power is restrored the display will not re-appear even though the hotplate may still be hot. 11 OPERATING OPERATING Hotplate blocking function Blocking of the hotplates prevents accidental changes while they are operating. The initial selections are maintained and the indicators remain active. The hotplates should be blocked to prevent children from operating them or to prevent the effects of accidental contact with cookware or utensils. Press the blocking sensor until its pilot light comes on. Unblocking Touch the blocking sensor until its indicator pilot light switches off. Double hotplate The cooktops sources that have double heat source when touching the corresponding sensors to said heat source only work with their small circuit . To operate the outer part, touch the double hotplate sensor until its indicator pilot light comes on, switch off by touching the sensor until the pilot light switches off. Focus hotplate The cooktops, which have the source of the heat source when acting over the corresponding sensors of each heat source, only work with their circular circuit. To switch on the outer part as well, touch the source hotplate sensor 0 until its control point switches on. To switch off the focus hotplate, touch the focus hotplate sensor 0 until the control point switches off. Multi-ring Hotplate The hobs, which have a multi-ring heat source, on touching the corresponding sensors to said heat source, only work with little resistance. If you wish the center ring to come on as well, touch the double ring sensor so that the sensor’s control point lights up. To use the ring to heat a multi-ring pan, touch the sensor . To switch off the two functions just touch the corresponding sensors again and . 12 OPERATING OPERATING (9 Quick Heating) Each control area includes an automatic programming function for quick heating. This programming allows the corresponding maximum temperature to be reached quickly and maintained automatically. Touch sensor + once and it is in position 9, the corresponding decimal point to 9 will switch itself on. Touching sensor of the same zone will decrease to the required level (levels 3…6 are recommended). After having reached the automatic heating time a short signal could be heard and the decimal point will switch itself off. The heat source carries on work in a conventional manner. To cancel the automatic programming touch the - sensor and the decimal point will switch off. 13 SAFETY SAFETY SPECIAL CONSIDERATIONS Safety systems In order to protect the electronics from overheating if the control unit detects excessive heat it will switch off the hotplate closest to the sensors and the letter H will appear on the display. This hotplate can be activated when the temperature of the electronic unit returns to normal. Each hotplate is equiped with an interior temperature limiter that switches off the hotplate if the radiant surface is heated excessively. If any cracks appear in the radiant surface, immediately disconnect it from the mains. Do not use any part of the cooktop until a new radiant surface has been fitted. Automatic If a hotplate is left on accidentally, it will automatically be switched off after a period of time has elapsed, depending on the power level that has been selected (level 1 - 10 hours, level 9 - 1 hour). If more than one sensor is pressed simultaneously, the keys are blocked. If all the power levels are at 0, the control is automatically switched off after 5 seconds. If one or more sensors are p...

Download now

Please, enter two numbers from picture: