(If this tumbler changes ownership, be sure this manual accompanies the tumbler.) Installation/ Part No. M414545 September 2002 TABLE OF CONTENTS SECTION I Safety Important Safety Instructions. . . . . . . . . . . . . . . . . . 5 SECTION II Introduction Information for Handy Reference . . . . . . . . . . . . . . 7 Parts Ordering Information . . . . . . . . . . . . . . . . . . . 8 Nameplate Location . . . . . . . . . . . . . . . . . . . . . . . . . 8 Roughing-In Dimensions and Specifications Cabi

To configure your 208V or 240V tumbler for 208V operation, you must remove the 240V configuration jumper located in the contactor box and replace it with the 208V jumper supplied with the information packet. This must be done prior to supplying power to machine. Failure to install proper configuration jumper may result in damage to sensitive electronic controls and may void warranty. To configure your 380V or 415V tumbler for 415V operation, you must remove the 380V configuration jumper located

Electric dryer is connected to a 208 volt circuit. Drying time will be 20% longer than drying on a 240 volt circuit. Drying procedures have not been followed. See Drying Procedures, page 4. Outside exhaust hood or exhaust duct may be clogged or restricted. Clean out any obstruction. High humidity. Use a dehumidifier near the dryer. Excessive wrinkling. Dryer is overloaded. Do not overload. See Drying Procedures, page 4. Items left in dryer too long. Remove items as soon as cycle ends. Insufficie

If it is necessary to reset the drying and cooling times for the current cycle, press STOP once to stop the tumbler. Press STOP again to cancel the cycle. If it is necessary to change programs during a current cycle, press STOP once to stop the tumbler and press STOP again to cancel the current cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions DMP Coin DV Control Suffix Description of The Coin Control Panel Refer to Figure 5. TMB1955N 1 Clock Symbo

Then set the reverse control switch to “nonreversing” and note that the cylinder turns constantly clockwise as viewed from the front of the tumbler. If not, interchange L1 and L2 power leads to the reverse drive motor. M414545 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 53 ELECTRONICALLY CONTROLLED OPL TUMBLER INTRODUCTION Drying can be done automatically or by time dry. When drying automatically, the tumbler stops drying when laundry reaches the factory set or programmed

If you choose to use a screw lock, then the special bracket (located inside the meter case) must be used. DO NOT use the special bracket if a 1/4 turn lock is used. Coin Drawer Security — for additional security, drill out the two pilot holes on each front side of the meter case to 1/4 or 5/16 inch (6.4 or 8.0 mm) holes and install a bicycle lock through these holes. Timer Cams . (Metered Models) The dryer timer is factory equipped with a 45 minute timing cam. If this drying time is not suit

Use an acceptable indicating device connected to the center grounding pin of the plug and the green screw on the back of the cabinet. 10. Reinstall access cover and screw. 512685 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 21 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 22 512685 Step 5: Reverse Door, if Desired NOTE: Doors with windows cannot be reversed. The door on this dryer is completely reversible. To reverse door proceed as follo

11. To reduce the risk of fire, DO NOT DRY plastics or articles containing foam rubber or similarly textured rubberlike materials. 12. Always clean the lint filter daily. 13. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt. 14. The interior of the tumble dryer and the exhaust duct should be cleaned periodically by qualified service personnel. 15. If not installed, operated and maintained in accordance with the manufacturer’s in

41 Electrical Requirements..................................................................... 45 Grounding Instructions ......................................................................... 45 For CE Models Only........................................................................ 45 Service/Ground Location...................................................................... 46 Connecting Electrical Service............................................................... 47 Configuring Yo