Too high temperatures may cause damage to them. ........ 2..LaundryloadingOpenthedoorandplacethetreatedlaundryintothedrumofthedryer. Tosaveenergyandachieveabetterdryingresult,pleasespinthelaundryasdryaspossible.Placethelaundryevenlyintothedrumaftershakethemloose. Note:Donotputexcesslaundryintothedryertoavoiddamagetothedryerandlaundry. 3..SettingdryingprogramTurntheprogramknobtosetanoptimaldryingprogramaccordingtothelaundrytypeandthedryingresultdesiredtoachieve. 4.DelicatefunctionsettingForthedel

Electric dryer is connected to a 208 volt circuit. Drying time will be 20% longer than drying on a 240 volt circuit. Drying procedures have not been followed. See Drying Procedures, page 4. Outside exhaust hood or exhaust duct may be clogged or restricted. Clean out any obstruction. High humidity. Use a dehumidifier near the dryer. Excessive wrinkling. Dryer is overloaded. Do not overload. See Drying Procedures, page 4. Items left in dryer too long. Remove items as soon as cycle ends. Insufficie

• For delicate clothes or less load, two towels may be added to get better drying and wrinkle-proof effects. • Do not excessively dry clothes to avoid wrinkles, shrinkage, roughness, electro-static charge accumulation, and/or more lint. 20 English AUTO DRY CYCLE 1. Turn the knob to any program except “Off” to power on. The control panel will beep once and the dryer will change from “Off” to the operating status. 2. Set the cycle select dial to required auto dry cycle. The temperature level is pr

For technical assistance, call (920) 748-3121. Page 5 SYMBOLS The following symbols are used in this manual and/or on the machine. Symbol Description NOTE! Hot! Do Not Touch Hei.! Nicht Beruhren Haute temperature! Ne pastoucher Caliente! no tocar dangerous voltage tension dangereuseGefahrliche elektrische Spannungtension peligrosa on marche Ein conectado off arret Aus desconectado start demarrage Start arranque de un movimiento emission of heat in general emission de chaleur en general Warmeabga

This will enable you to disconnect the steam connections and service the dryer while your plant is in operation. 5. Before connecting trap and check valve to dryer, open globe valve in steam supply line and allow steam to flow through dryer to flush out any dirt and scale from dryer. This will assure proper operation of trap when connected. 6. After flushing system, install bucket trap (with built-in strainer) and check valve. For successful operation of dryer, install trap 18" (458 mm) below

Ready to wear 7 kg Ready to iron 7 kg 7 kg Ordinary cotton fabrics Ready to wear Ready to iron 3 kg 3 kg Ordinary synthetic fabrics Timer 20 min Timer 40 min Timer 60 min 7 kg 7 kg 7 kg Heavy fabrics, needing further drying. 7 kg / * Programme setting for testing in accordance with EN 61121. /0.5 kg * 20 60 40 1.Turning on power Insert the power plug into an appropriate wall socket and turn on the power.. Operating power supply: (220-240)V/50Hz. 2. Laundry loadingOpen the door and place the laun

(102 cm) Coin Slide Models *4.5 in. (11.4 cm) *15.44 in. (39.2 cm) 21.56 in. (54.8 cm) Coin Slide Models *38.19 in. (97 cm) Electronic Control Models *43 in. (109.2 cm) Standard Capacity Meter case *43.875 in. (111.4 cm) High Capacity Metercase DRY2238 GAS MODELS 23.5 in. (59.7 cm) 8.0 in. (20.3 cm) 28 in. (71.1 cm) *38.19 in. (97 cm) Electronic Control 15.4 in. (39.1 cm) 2.3 in. (6 cm) 26.875 in. (68.3 cm) 0.4 in. (1.02 cm) 2.8 in. (7 cm) 1 22.06 in. (56 cm) Electronic Control Models *4.5 in. (

If necessary, put small items into a net. ¦To achieve a better drying result, shake the heavy laundry and make it loose before load it into the dryer. Dry at normal temperature Dry at reduced temperature Drying in the tumble dryer not possible Drain switchover During the drying of the laundry, the condensate water is automatically collected in the box inside the machine, so that the water needs to 12 1.Cleaning the surface Wipe the body of the dryer and the control panel with a damp cloth. Remem

Exhaust ducts shall be constructed of sheet metal or other noncombustible material. Such ducts must be equivalent in strength and corrosion resistance to ducts made of galvanized sheet steel not less than 0.0195 inches (0.495 mm) thick. Where the exhaust duct pierces a combustible wall or ceiling, an opening having a diameter of 4 inches (10.2 cm) larger than the diameter of the exhaust duct shall be provided, with the duct centered in the opening. When ducts pass through walls, ceilings, floors

If the dryer is overloaded, it could cause discoloration or permanent heat damage to the load. • There should be space in the dryer for the clothes to tumble freely and help to reduce wrinkles. • Large and small pieces together make up loads which will tumble well. Permanent press loads should be smaller to provide room for tumbling. Proper tumbling allows for fewer wrinkles. • A load can be too small. Just a few small pieces will not tumble properly. They will take longer to dry and they may be