Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  
downloaded: 0   File size: 4 mb   Manafacture: Grizzly  
Category: Sanders
@name

As a result, the wiring pages and electrical parts in the original manual no longer match what is on the machine. This manual update shows the new wiring and parts that reflect the changes. At the top of each new section is a note that indicates which page it replaces in the original manual. On the parts list, the new parts are designated with a "V2". All changes indicated in this update are effective for machines manufactured September, 2010 and after. Before operating your new machine, you MU

downloaded: 0   File size: 4 mb   Manafacture: Grizzly  
Category: Sanders
@name

Feed belt tension adjustment bolts. Note: Safety guard removed for clarity. 4. When tensioned properly you should not be able to lift the feed belt off the table surface or slide it back and forth. Awarning DO NOT sand boards with the guard removed. Failure to follow this warning could result in serious personal injury. NOTICE Adjust the feed belt tension before adjusting the feed belt tracking. To adjust the feed belt tracking: 1. Turn the feed belt ON. 2. If the feed belt is tracking t

downloaded: 0   File size: 4 mb   Manafacture: Grizzly  
Category: Sanders
@name

downloaded: 0   File size: 10 mb   Manafacture: Grizzly  
Category: Sanders
@name

WASHR 3/8 (G0582/G0445) 5318 P05825318 HANDLE (G0582/G0445) 5319 PSS08 SET SCREW 5/16-18 X 1/2 5320 P05825320 ADJUSTMENT RING (G0582/G0445) 5321 PB03 HEX BOLT 5/16-18 X 1 (G0582/G0445) 5322 PW07 FLAT WASHER 5/16 (G0582/G0445) 5323 P05825323 HANDLE (G0582/G0445) 5401 P05825401 HOUSING (G0582/G0445) 5401 P9962Z5401 HOUSING (G9962Z/G9962ZX) 5402 P05825402 ROLLER (G0582/G0445) 5402 P9962Z5402 ROLLER (G9962Z/G9962ZX) 5403 P9962Z5403 FASTENING TUBE 5405 P05825405 PULLEY (G0582/G0445) 5405

downloaded: 0   File size: 543 kb   Manafacture: Grizzly  
Category: Sanders
@name

The Model T21319 can bend up to 18 gauge (0.473 in. or 12mm) mild steel. Figure 1. Model T21319 24" Bending Brake. Inventory (Figure 2) A. Bending Brake Assembly...........................1 B. Clamping Angle..........................................1 C. Clamp Assemblies......................................2 D. Breaker Bar Levers.....................................2 E. Hardware Bag (not shown) — Hex Bolts M10-1.25 x 30........................4 — Hex Nuts M10............................

downloaded: 1   File size: 1 mb   Manafacture: Grizzly  
Category: Sanders

downloaded: 4   File size: 1 mb   Manafacture: Grizzly  
Category: Sanders

downloaded: 0   File size: 10 mb   Manafacture: Grizzly  
Category: Sanders
@name

3. Replace conveyor belt. Straight strip of notches on workpiece. 1. Pressure rollers are dirty or damaged. 1. Clean or repair pressure rollers. Awarning For your safety, turn the power switch off and disconnect the sander from the power source and the air supply before starting the applicable troubleshooting. -40- o G0445/G0582/G9962Z/9962ZX Wide Belt Sander Troubleshooting SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Snake shaped marks on workpiece. 1. Sanding belt damaged or dirty. 1. Cl

downloaded: 10   File size: 4 mb   Manafacture: Grizzly  
Category: Sanders

downloaded: 4   File size: 10 mb   Manafacture: Grizzly  
Category: Sanders
@name

4. Motor overloaded. 1. Repair or replace connections on motor for loose or shorted terminals or worn insulation. 2. Correct the low voltage conditions. 3. Install correct fuses or circuit breakers. 4. Reduce load on motor. Drums run backwards (G0450 only). 1. Two of the power wires are reversed (G0450 only). 1. Switch two of the current carrying wires at the main power block (G0450 only). Machine slows when sanding, making a squealing noise, especially on start-up. 1. V-belts loose. 2. V-belts





Category