Alternatively, press ior kon the remote control. You can tune in the desired preset station directly by pressing the numbered buttons on the remote control. -To select preset number 25, press 2 and 5. -To select preset number 7, press 7. To clear a preset station 1Tune in the station by preset tuning. 2 Press ENTER, and press ENTER again while the frequency flashes on the display. Alternatively, press ENTER or C on the remote control, and press ENTER while the frequency flashes on the display. R

11 CONEXIONES .........................................................13 CONEXION DE LOS ALTAVOCES SUMINISTRADOS ....13 CONEXION DEL CORDON CA ......................................... 13 CONEXION DE LAS ANTENAS ........................................15 CONTROL REMOTO ....................................m.....m....m....m.m.ml7 OTRAS CONEXIONES ......................................................l7 PREPARATIVES .....................................................l9 ANTES DELAOPERACION ......

it can store a total of 30 signal codes of the external remote control. Use the remote control. 1 Press the LEARN button. “ADDRESS flashes on the display window. 2 Press one of the MEMORY buttons (A-O), then the ADDRESS 1 or 2 button to designate the button on which the signal code is stored. The indication you designated appears on the display. Example: When designating the ADDRESS 1 on the MEMORY A button. 3 Pointing the remote control of the connected equipment toward the unit, press the func

• The unit plays only the audio tracks if a disc contains both audio tracks and MP3 files. • When playing a disc of 8k bps or VBR*, the elapsed playing time in the display window will not be correct and also the intro play may not function properly. * VBR: Variable Bit Rate Notes on indications in the display • Up to 32 characters are displayed for the name of an album or a track. Characters other than uppercase letters (“A” to “Z”), lowercase letters (“a” to “z”), numerals (“0” to “9”), and und

RADIO RECEPTION (cont.) pg. 11 PRESETTING STATIONS The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Press TUNER to select a band, and press the UP or DOWN button to select a station. Direct tuning is also available. 2 Press the SET button to store the station. A station is assigned a preset number, beginning from 1 in consecutive order for each band. 3 Repeat st

When the front speakers are turned on, “SP3” lights up on the display window. NOTE • When you turn off the front speakers, the surround mode (Dolby Digital, Dolby Pro Logic or DTS) or the DSP mode will be canceled. • When the front speakers are turned off, SURROUND and DSP on the front panel cannot be used. (“CAN’T USE” will be displayed). CONNECTING THE SUPPLIED ANTENNAS 2 22222 Connect the FM antenna to the FM 75. terminal and the AM antenna to the AM LOOP jack. FM antenna ANTENNA AM LOOP FM 7

“TAPE ON” appears on the display for four seconds, and then the source name selected in step 1 comes back on. To cancel the tape monitor, press it again so that “TAPE oFF” appears. . Any sound control except the BBE system has no effect on recording (see page 7). Recorded sound cannot be monitored if the connected tape deck is not a three-head system. 9 ENGLISH DIRECT TUNING MONO 1,2 3 DOWN~, UPA TUNER I II 1 Press the TUNER button repeatedly to select the desired band. ~ If the power is turned

Be sure to set the FRONT SPEAKERS A and B buttons to 10FF. Otherwise sound is output from the speakers. The 5.1 CH function, Dolby Pro Logic or DSP system is automatically canceled when the headphones are plugged in. To turn the unit off, press the POWER button. 7 ENGLISH DOWN,UP VOLUME VOL I MUTING I BALANCE T-BASS VOLUME CONTROL Turn the VOLUME control on the unit, or press the VOL buttons on the remote control. The vc)lume level is shown on the display for four seconds. It can be adjusted bet

09-005-422-5T3). • This Service Manual contains information about the difference between Z-L200 (LH) and Z-L200 (HA). If requiring other information, see Service Manual of Z-L100 (U) / 200 (LH), (S/M Code No. 09-99C-422-5R1). DATA S/M Code No. 09-006-422-5S1 • If requiring information about the CD mechanism, see Service Manual of AZG-1, (S/M Code No. 09-001-335-3NC). SPECIFICATIONS Tuning range 87.5 MHz to 108 MHz Usable sensitivity (IHF) 13.2 dBf Antenna terminals 75 ohms (un

When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Turn the FUNCTION selector to select theTUNER function, and press the VIDEO 1/5.1 CH/BAND button repeatedly to select the desired band. Then press the UP or DOWN button to select a station. 2 Press the ENTER button to store the station. A preset number assigned to the station, beginning from 1 in consecutive order for each band, is displayed for two seconds. 3 Re