Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 0   File size: 607 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name

BRIDGED BRIDGED BATT REM GND CH1 CH2 CH3 CH4 FUSE LEFT SPEAKER OR SUB-WOOFER 4-8 OHMS RIGHT SPEAKER OR SUB-WOOFER 4-8 OHMS 2-CHANNEL MONO (BRIDGED) OUTPUT WIRING DIAGRAM USE #10 GAUGE WIRE (SEE TEXT) Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling off to a normal operating range.

downloaded: 2   File size: 2 mb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name@name

Note • The exposed conductor should be 5/16 inch (7 mm) to 7/16 inch (10 mm) long. – If shorter, it may cause a poor conductivity. – If longer, it may cause a short circuit. • Use a proper hex wrench for each terminal. – 4 mm: +B terminal and GND terminal – 3 mm: REM terminal and speaker terminals 2 Subwoofer system 2-subwoofer system (2 amplifi ers) 2-subwoofer system 4-speaker system plus subwoofer—5.1-channel (3 amplifi ers) Connection varies depending on the number of the speakers used in yo

downloaded: 0   File size: 285 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name

If fuses blow consistently, carefully check all electrical connections to the unit. 5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery and chassis ground must mustmustmustmustmust be of a thick enough gauge to provide this voltage to the amplifier. We recommend #10 #10#10#10#10#10 gauge wire or larger (smaller gauge #) for the battery and ground leads. 6. Make certain that the speaker(s) to be used with this amplifier is cap

downloaded: 1   File size: 1 mb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name@name@name

PREPARATION Getting Started It’s a good idea to read all of the instructions before beginning the installation. Contents Installation Instructions.............................. 3 Wiring ........................................................ 5 Installing the Removable Faceplate .......... 6 Operating Instructions ............................... 7 CD Player Operating Instructions............ 10 MP3 Player Operation (PMP180U) ......... 12 CD Changer Controls (PMP180U) .......... 13 Care and Maint

downloaded: 15   File size: 309 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name

4 - 5 4-Channel and Mixed-Mono Input Wiring Diagram .................... 6 4-Channel and Mixed-Mono Output Wiring Diagram ................. 7 3-Channel Input Wiring Diagram ................................................ 8 3-Channel Output Wiring Diagram ............................................. 9 2- Channel Mono (Bridged) Input Wiring Diagram .................... 10 2-Channel Mono (Bridged) Output Wiring Diagram ................... 11 Operation .............................................

downloaded: 0   File size: 236 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name

Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. For leads in excess of 10 feet, #16 gauge is recommended. When wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity of the correspondi

downloaded: 1   File size: 619 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name@name

Other uses might include limiting the low frequencies to smaller speakers (61/2", 6 X 9", etc.) by adjusting the crossover to a higher setting (80 – 100Hz). Crossover (X-OVER) The JPA series of amplifiers have built-in low-pass and highpass crossover filters for bi-amplifying the system. Adjust the crossover to accommodate your chosen installation method. Select LPF (low pass filter) when the amplifier will be driving woofers or subwoofers. Choose FULL when crossover mode is not active and the a

downloaded: 3   File size: 252 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name

If the car stereo does not provide an Auto-Antenna lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in the car's fuse block. This will turn the amplifier on and off with the ignition key, regardless of whether the car stereo is on or off. The remote turn-on lead does not carry large currents, so #20 gauge -4 wire may be used for this application. WIRINGINSTRUCTIONSWIRINGINSTRUCTIONS 4. Speaker Connections Depending on the type and number of speakers used with the

downloaded: 5   File size: 270 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name

Use good quality shielded audio cables with RCA plugs at both ends to connect the stereo to the amplifier and keep the cable lengths to a minimum to avoid noise. If the car stereo does not provide low-level outputs, the amplifier may be connected via the speaker (high-level) outputs from the stereo. Wire the speaker leads from the car stereo to the 5-pin adaptor harnesses as shown in the diagram (shielded cable is not required for this application) and plug the connectors into the mating High-Le

downloaded: 0   File size: 1004 kb   Manafacture: Audiovox  
Category: Receivers & Amplifiers
@name@name@name

Specifications CEA Power Ratings PS260 Power Output: 57 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Additional Power Output: 75 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 155 watts RMS X 1 channel (Bridged mono) into 4-ohms @ < 1% THD+N Dynamic Power: 114 watts X 2 channels into 4-ohms Dimensions: 7" X 12" X 2 ." (180mm X 302mm X 55.5mm) PS285 Power Output: 80 watts RMS X 2 channels into 4-ohms @ < 1% THD+N Additional Power Output: 105 watts RMS X 2 channels into 2-ohms @ < 1% THD+N 215





Category