Votes - 5, Average rating: 4.2 ( )

Manafacture: Aiwa File size: 6.9 mb File name: AVX100.pdf Language of manual:

“TAPE ON” appears on the display for four seconds, and then the source name selected in step 1 comes back on. To cancel the tape monitor, press it again so that “TAPE oFF” appears. . Any sound control except the BBE system has no effect on recording (see page 7). Recorded sound cannot be monitored if the connected tape deck is not a three-head system. 9 ENGLISH DIRECT TUNING MONO 1,2 3 DOWN~, UPA TUNER I II 1 Press the TUNER button repeatedly to select the desired band. ~ If the power is turned off, the previously tuned station will be played (Direct Play Function). 2 Press the UPA or DOWNY button to select a ~tati~nm E:ach time the button is pressed, the frequency changes. When a station is received, “TUNE” is displayed for two seconds. During FM stereo reception, (I(O)]) k displayed. To search for a station quickly (Auto Search) Keep the UPA or DOWNV button pressed until the tuner starts searching for a station. After tuning in to a station, the search stops. To stop the Auto Search manually, press the UPA or DOWNY button. o The Auto Search may not stop at stations with very weak sifgnals. When an FM stereo broadcast contains noise Press the MONO TUNER button on the remote control so that “MCINO appears on the display. Noise is reduced, although reception is monaural. To restore stereo reception, press the butkm so that MONO disappears. To change the AM tuning interval The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the frequency allocation system is 9 kHz/step, change the tuning interval. Hold down the TUNER button and press the POWER button ~?ediatelv. Note that the unit is set to the Direct Tuning mode if the TUNER button is pressed and held down for about two seconds. To reset the interval, repeat this procedure. When you know the frequency of the desired station, you can tune in directly to the station. 1 Press the TUNER button to select a band. 2 Press the TUNER button and hold it down until “—“ flashes on the display (Direct Tuning Mode). 3 Press the appropriate numeric buttons to tune in to the desired station. Example: To tune in to 106.50 MHz, Dress 1, 0, 6, 5 and O buttons. To tune in to 95.25 MHz, p;ess 9, 5, 2 and 5 buttons. To cancel the Direct tuning mode Press the UPA or DOWNY button. When entering a frequency out of tuning range, the value flashes for two seconds and then goes off. Check the frequency and repeat step 3 correctly. When entering a frequency not covered by the tuning interval, the value is automatically rounded up or down to the closest one covered by it. ENGLISH 10 PRESET NUMBER TUNING PRESETTING STATIONS Tl?e unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Press the TUNER button to select the band, and press the UPA or DOWN7 button to select a station. Direct tuning is also available. 2 Press the SET button to store the station. A station is assigned a preset number, beginning from 1 in consecutive order for each band. Preset“number 3 Repeat steps 1 and 2. No more stations will be stored if a total of 32 stations have already been stored for all the bands. Em When the AM tuning interval is changed, all preset stations are cleared. The preset stations have to be set again. 1 Press the TUNER button to select a band. 2 Press the numeric buttons to select a preset number. Example: To select preset number 25, press 2 and 5. To select preset number 7, press O and 7. To clear a preset station Select the preset number of the station to be cleared. Then, press the SET button, and press the SET button again within four seconds. The preset numbers of all other stations in the band with higher numbers are decreased by one. I1 ENGUSH The Dolby Pro Logic feature and the center and surround speakers (standard) assure full-scale home theater sound. When playing back laser discs or video software that have been specially recorded with four-channel sound (left, right, center, surround) and steering logic (for directing sound), astonishingly realistic sound surrounds the listener to create a new level of audio/visual entertainment. Independent control of the four channels allows the listener to enjoy the same type of sound reproduction experienced in movie theaters. Voices are reproduced in the front and center sound field, while ambient sounds like cars and crowds are reproduced on all sides of the listener for an incredibly lifelike audio/video experience. Please read the following carefully to “tune” the system’s output to match the characteristics of your listening space. Check the following: * Before using the DOLBY PRO LOGIC, adjust the proper balance of the speaker sound levels (see page 13). o Make sure the speakers are properly connected and positioned (see pages 3 and 4). o Make sure the TV set and video unit are properly connected (see page 3). * Make sure the laser disc and video tape, etc., suppor...

Download now

Please, enter two numbers from picture: