2. Clean/Solution Tank Is located to the right of the unit when you are facing the unit. Automatic Smart System™ Control PaneI located in the center of the unit and is where you will begin selection of the Smart Cleaning Cycle you would like to use (Detailed instructions on page 8). Dirty/Collection Tank Looking at the front of the unit, the Dirty/Collection tank is on the left side. Vacuum Flex Hose wraps around the center of the 3. 4. 7 unit. This serves as the travel path for dirty water and

Filters are dirty 5. Check and clean filter 6. Hose not properly attached 6. Make sure hose collar is pushed in or in locked position 7. Vacuum is not suctioning or blowing 7. Make sure hose is in correct inlet/outlet Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. If you should happen to need assistance during assembly or operation, call 1-800-237-7691. Please do not return this produ

5. Tocleanattachments,removefromhoseand rinseinclean,runningwater.Drybeforestoring. Cleanthehosebysuctioningcleanwaterfroma bowl.Beforewrappingbackonmachine,liftend ofhoseandstretchouttoensureallwateris clearedfromhose.Refertopage10, illustrations11and12. 6. Wipe the machine’s exterior with a soft cloth. 7. After carpet is dry, vacuum again to remove hair and fuzz. Machine storage Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this produ

Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer. 2. Check for colourfastness in an inconspicuous place. 3. If possible, check upholstery stuffing. Coloured stuffing may bleed through fabric when wet. 4. Plan activities to give upholstery time to dry. 5. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts. 6. To begin cleaning with attachment

4. WARNING: Use only BISSELL Little Green formula in yourcleaner. Use of cleaningformulas which contain lemon or pine oil maydamage this applianceand void warranty. Chemical spot cleanersor solvent-based soil removers should not be used. These productsmay react with the plastic materials used in your cleaner, causingcracking or pitting. POWER HEATER Power Switch Heater Switch Heat Indicator Light B R US H S U C T IO N 7 Remove Vacuum Flex Hose completely from On Board Hose Storage. Attach 4” Too

Take care not to run over loose objects oredges of area rugs. Stallingbrush may result in premature belt failure. Tip: make only one trip to the sink by removing the entire portable cleaner. fill and empty in the same trip. 4. 2. 3. WARNING: to reduce the risk of fire, electric shock, or injury, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. Tip: for best results empty, rinse and dry both tanks before storing. 800.237.7691 9 Operations

Return Tank-in-Tank to the machine. NOTE: Always check the level of cleaning formula in the SmartMix tank at the same time, and refill as needed Rinse (optional) Rinsing is an optional step that can be done during the cleaning process by switching to the water rinse setting, or it can be done after the carpeted area has been cleaned. 1. Simply choose the water rinse setting on the SmartMix dial, and follow the same path as you did for cleaning, taking care to do a forward (wet) stroke by depress

These products may react with theplastic materials used inyour QuickSteamer,® causing cracking or pitting. Tip: Always vacuum thoroughly before you deep clean. If possible, move larger furniture to an area you will not be cleaning. 2. Formula Measuring Cap Unscrew to Remove 6. Power Switch 7Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. Spray soiled area with BISSELL® Tough Stain PreCleaner.™ Use a stiff-bristled brush to work formula into carpet pil

4. Repeat motion over same area without depressing Trigger. 5. Repeat Steps 3 and 4 until no more dirt can be removed. 6. Continue to clean entire carpet, working in 3’ x 4’ sections. 7. Empty the Dirty Water Tank Assembly when dirty water reaches the fill line. 8. If the machine loses suction and/or motor noise rises in pitch, turn Power Switch to OFF. Check the Dirty Water Tank Assembly and empty the tank if it is full [see WHEN YOU’RE DONE, page 6]. 9. If floor nozzle stops spraying, turn Pow