Votes - 2, Average rating: 5
(
)
)
|
manual abstract
2. Clean/Solution Tank Is located to the right of the unit when you are facing the unit. Automatic Smart System™ Control PaneI located in the center of the unit and is where you will begin selection of the Smart Cleaning Cycle you would like to use (Detailed instructions on page 8). Dirty/Collection Tank Looking at the front of the unit, the Dirty/Collection tank is on the left side. Vacuum Flex Hose wraps around the center of the 3. 4. 7 unit. This serves as the travel path for dirty water and formula that is suctioned up into the Dirty/ Collection tank. Vacuum Flex Hose Release Button Press this button to release the Flex Hose to attach the Tough Stain Brush for manual cleaning. Spray Trigger When cleaning in the Manual Mode, depress the Spray Trigger to spray water and formula unto the area to be cleaned. Storage Tray (Select Models Only) Is provided for when the unit is stored. Underside View Handsfree Cleaning Brushes Provide the cleaning action when using the Surface Stain or Set-In Handsfree Cleaning cycles. Spray Tip Water and Solution are dispensed here when cleaning in the Handsfree mode. Vacuum Suction Nozzles Provide the suction path when using the Handsfree Cleaning cycles. Back View Handsfree Cleaning Window Provides an area to see the Handsfree Cleaning Action. Flex Hose Clip Is attached to the unit and is a guide for the Vacuum Flex Hose. Tough Stain Brush™ Storage The Tough Stain Brush is conveniently stored on board. Power Cord Has a three-prong plug and stores on the back of the unit around the Oval Cord Wrap. NOTE: Unwrap the Power Cord completely before operating the unit. Oval Cord Wrap Serves as a guide for the Power Cord for storage. The Oval Cord Wrap can be gently pushed in during use. 7. 8. 10. 13. 14. 5. 6. 9. 11. 12. 15. ug203-6650_1200_805.indd 11/1/05 11:44:28 AM ug203-6650_1200_805.indd7 77 11/1/05 11:44:28 AM 8 To fill the Clean Tank: Remove the Clean Tank by lifting it straight up and then away from the unit. Unscrew the cap at the bottom of the Clean Tank. There are 2 ways you can fill and use the tank: For common stains such as dirt, grime, pet, or oily stains, use the fill lines on the left side of the tank and fill with Little Green formula (trial sizes included) and water. For dye based stains such as coffee, fruit juices, cola and red wine, use the fill lines on the right hand side of the unit and fill with Little Green and Oxy GEN2 formulas (trial sizes included) and water. Using the Automatic Smart System™ Your new SpotBot features an Automatic Smart System that takes the guesswork out of spot and stain cleaning. With the touch of a button, you can select the cleaning cycle to use your preferred method of cleaning. Surface Stain Cycle This cycle has been designed for stains that are on the surface of your carpeting. Typically the stains that have just happened and have not had time to penetrate deep into your carpet fibers. This cycle will run for approximately 3 minutes. Set-In Stain Cycle This will serve best on stains that have had a period of time to set-in and penetrate deep into your carpet fibers. These are typically the most difficult stain types to remove. This cycle runs for approximately 6 minutes. Manual / Hose By selecting this option you can clean spots and stains manually on surfaces such as upholstery, car interiors, stairs or anyplace you have a need to clean yourself. 1. A. 1. 2. 3. A. Getting Ready B. How To Begin 2. 3. B. 2. 3. Tip: Before spot cleaning with the SpotBot's Handsfree feature, dry vacuum the area first. 8 To fill the Clean Tank: Remove the Clean Tank by lifting it straight up and then away from the unit. Unscrew the cap at the bottom of the Clean Tank. There are 2 ways you can fill and use the tank: For common stains such as dirt, grime, pet, or oily stains, use the fill lines on the left side of the tank and fill with Little Green formula (trial sizes included) and water. For dye based stains such as coffee, fruit juices, cola and red wine, use the fill lines on the right hand side of the unit and fill with Little Green and Oxy GEN2 formulas (trial sizes included) and water. Using the Automatic Smart System™ Your new SpotBot features an Automatic Smart System that takes the guesswork out of spot and stain cleaning. With the touch of a button, you can select the cleaning cycle to use your preferred method of cleaning. Surface Stain Cycle This cycle has been designed for stains that are on the surface of your carpeting. Typically the stains that have just happened and have not had time to penetrate deep into your carpet fibers. This cycle will run for approximately 3 minutes. Set-In Stain Cycle This will serve best on stains that have had a period of time to set-in and penetrate deep into your carpet fibers. These are typically the most difficult stain types to remove. This cycle runs for approximately 6 minutes. Manual / Hose By selecting this option you can clean spots and stains manually on surfaces such as upholstery, car interio...