Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Modification of this product can be extremely hazardous and could result in personal injury or property damage. MODEL INSTALLATION & OPERATING 9093100-(X)PR INSTRUCTIONS 9093200-(X)PR Important: Instructions Form No. 3308407.000 4/03 must stay with unit. ©2003 Dometic AB Owner read carefully. Torggatan 8 SE-171 54 Solna CENTRAL RV VACUUM SAFETY INSTRUCTIONS This manual has safety information and instructions to help users eliminate or reduce the risk of accidents and injuries. RECOGNIZE SAFETY INFORMATION ! This is the safety-alert symbol. When you see this symbol in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating instructions. UNDERSTAND SIGNAL WORDS A signal word , WARNING OR CAUTION is used with the safety-alert symbol. They give the level of risk for potential injury. WARNING! indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION! indicates a potentially hazardous situation which, if not avoided may result in minor or moderate injury. CAUTION used without the safety alert symbol indicates, a potentially hazardous situation which, if not avoided may result in property damage. Read and follow all safety information and instructions. 2 CENTRAL RV VACUUM SPECIFICATIONS: MODEL NUMBER CODE CHART 9093(X)00-(X)PR Electrical Rating 240VAC 50/60 Hz, 1 Ph Amp Draw 11 Amps Minimum Wire Size 16 AWG AC Circuit Protection 7.5 Amp Installed Weight 12 Lbs. Hose Length 8’ - 30’ Case Steel powder coat 1 = Flush Mount 2 = External Mount W/Mtg Brkt C = CREAM E = EBONY W = WHITE P = POWDER COAT R = RECREATION VEHICLE Part List: Tools Required: 9093(X)00-(X)PR Vacuum (1) Mounting Bracket* Screw Driver Power Drill (3) 3308150.006 Bags (4) Wood Screws* Level Electrical Wire (1) 3308172.000 Motor Filter (4) Painted Screws** 1/16” Drill Bit Drywall Anchors (1) Template** (1) 3303170.004 Exhaust Filter Awl (3) Wire Nuts** * Designates supplied with external mount vacuum. ** Designates supplied with flush mount vacuum. INSTALLATION I. GENERAL INFORMATION A. This Central RV Vacuum Cleaner is designed to be built into a recreational vehicle at the time of manufacture; or, with the use of an external mounting plate, it can be installed in a recreational vehicle after it has been manufactured. Read Installation and Operating Instructions carefully before attempting to start your vacuum cleaner installation. Attach mounting bracket to wall or surface at a comfortable operating height or if not possible a minimum of 6” above the floor. For hard surface mounting, use the 4 outer holes with wood screws. For drywall mounting, use 4 outer holes with drywall anchors (not supplied). See FIG. 1. BRACKET WITHINSTALL MOUNTING SCREW HOLES ABOVE KEYSTUDS Improper installation may damage equipment, could endanger life, cause serious injury and/or property damage. KEYSTUD B. LOCATION: 1. External Mount Installation 6” MIN a. To reach with vacuum hose as far as possible, FIG. 1 CLEARANCE choose a wall or surface that is centrally located and has an electrical outlet within 6 foot of c. Attach vacuum cleaner to the mounting bracket, vacuum cleaner. using the 4 keyholes in the back of the unit to the 4 studs on the mounting bracket, then slide unit down into locked position. d. Before plugging in the electrical cord, check to be sure vacuum cleaner bag, motor filter, exhaust filter, and gate are in place. See Operating Instructions, Steps D, E, and F. Note: Never use vacuum cleaner without dust bag or motor filter in place. WARNING! 3 CENTRAL RV VACUUM 2. Flush Mount installation a. To reach with vacuum hose as far as possible, choose a wall or surface that is centrally located and has a nearby 110 Volt AC power connection. The vacuum cleaner requires 3-7/8” wall depth (measured from the front of the wall). WARNING! There may be electrical wiring in the wall. Disconnect AC power cord and the positive (+) 12 volt DC terminal at the supply battery. Failure to follow this instruction may create a shock hazard causing death or severe personal injury. b. Attach paper template with tape to wall or surface a minimum of 6“ above the floor, if mounted in a vertical position. This will allow sufficient clearance for exhaust air. See FIG. 2. g. Test unit for operation before installing. Check to be sure vacuum cleaner bag, motor filter, exhaust filter and gate are in place. See Operating Instructions, Steps D, E, and F. Slide the unit , bottom first into the opening and secure to wall with the 4 wood screws. Note: Never use vacuum cleaner without dust bag or motor filter in place. Note: Optimal installation uses 6 wood screws instead of 4 to reduce risk of loosening due to road vibration. C. GROUNDING INSTRUCTIONS - EXTERNAL MOUNT 1. This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. See FIG. 3. D. GROUNDING INSTRUCTIO...
Other models in this manual:Vacuum Cleaners - 9093200-(X)PR (433.43 kb)