Radio-controlled time 2. Projection of time 3. LED backlight 4. Display of indoor temperature/humidity or alarm time 5. Time alarm ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal antenna in the projection alarm.

Replace only with new batteries of the recommended type. When cleaning the display and casings, use a soft damp cloth only. Do not use solvents or scouring agents as they may mark the LCD and casings. Do not submerge the unit in water. Furthermore, fix all parts in place where the units are adequately protected against moisture and rain. Special care shall be taken when handling a damaged LCD display. The liquid crystals can be harmful to user's health. Do not make any repair attempts to the uni

ADDITIONAL EQUIPMENT (not included) 1) Two fresh 1.5V AA batteries (optional for projection alarm clock) FEATURES OF PROJECTION ALARM Operation of these features is in section III 1. Radio-controlled time 2. Projection of time 3. LED backlight 4. Display of indoor temperature/humidity or alarm time 5. Time alarm ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and trans

If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects

In this time the display will show both the indoor temperature and humidity. If the station does not display both indoor temperature and indoor humidity after the 15 minutes please retry the set up as stated above. After both indoor temperature and indoor humidity are displayed for 15 minutes you can place your projection alarm in your desired location. To complete the set up of your temperature station after the 15 minutes have passed please follow the steps beginning on page 6. 4 DETAILED SET-

All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for th

3. Press and release the “SNOOZE” button to confirm the time setting and to advance to DST (Daylight Saving Time) setting. D. TIME ZONE SETTING 1. Hold down the “MODE/MIN” button for 3 seconds, the time will flash in the Time LCD. 2. Press and release the “SNOOZE” button to advance to the time zone selection. 3. In the indoor temperature/humidity section of the LCD the time zone will flash. 6 4. Press and release the “MODE/MIN” button to select the appropriate time zone. There are 24 time zones

The alarm repeats automatically after 24 hours. Page 4 of8 If the “ SNZ” button is pressed, the alarm will silence for approximately 5 minutes, after which it will begin to sound again. The alarm uses 3 different patterns of tone, beginning gently and increasing in intensity, known as a "Crescendo Alarm" . Battery Replacement Information To replace the battery: 1. Lift up the battery compartment cover and remove the battery. 2. Please take note to install the battery with the proper polarity as

NOTE: The above steps are not required but can help the projection alarm receive the signal faster. 3. Place the batteries into the projection alarm clock. 4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. NOTE: It is important to not press any buttons after inserting batteries as this will interrupt the WWVB search sequence. In this time the display will show both the indoor temperature and humidity. If the station does not display both indoor temperature and indoor humidity after the 15 minutes plea

All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for th