12082 Western Avenue, Garden Grove, CA 92841 (800) 874-3005 VOICE • (800) 772-2889 TTY/TDD • (714) 897-4703 FAX email: ameriphonecs@plantronics.com website: ® XL The Extra Loud & Clear XL-40 AMPLIFIED TELEPHONE with lighted keypad! Operating Instructions M46802 ©AMERIPHONE® XL-40 5270-4023 .A4/03 E N G L I S H E S P A N O L F R A N C A I S Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric sho

• Setup special features Installing the Backup Batteries To add extra brightness to the Dialogue XL-25s’s ring flasher when you receive calls, install one 9 Volt alkaline battery (not included). Note: For your safety always unplug the phone line before you install or replace the backup battery. 4 Figure 3 To install new battery: 1. Slide open the battery compart-ment cover on the bottom of the telephone, (Figure 3). 2. Install one fresh 9-volt battery. The battery indicator on the base unit will

Read and understand all instructions. Observe all warnings and other markings on the product. 2. During thunderstorms, avoid using telephones except cordless models. There may be a slight chance of electric shock from lightning. 3. Do not use a telephone near a gas leak. If you suspect a gas leak, report it immediately, but use a telephone away from the area where gas is leaking. 4. Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, o

3 E N G L I S H Important Safety Instructions CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalent Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalent Number of

Help from Ameriphone For help with using your DIALOGUE JB-20 , call our Customer Relations department at 800-894-3005. Please make sure your DIALOGUE JB-20 package includes the items shown in Figure 1. Base Unit CHAPTER 3 FEATURES IDENTIFICATION RINGER TONE selector HOLD button Ringer control switch (volume) Audio Output jack Tone / Pulse switch Emergency buttons Braille characters Raised letters for easy identification REDIAL button MEMORY button HANDSET VOL control (volume) FLASH button PROG b

K. Printing a Memo or Conversation Stored in Memory 1. With the TTY on, hold down Press 2 . and 2. Type in the name or press to scroll to the desired memo. 3. Press to select the memo. 4. Hold down and press P . This feature notifies the user who was placed on "HOLD" that the other party has resumed typing. Press and W simultaneously to activate this feature. The built-in signaler flashes when an incoming signal is being detected from the other party. Any keyboard activity cancels Wait-For-Respo

3. Press to select ASCII (or to not select). 4. Next, the screen summarizes the ASCII mode settings and then asks if you want to change modes . 5. Type Y to change. Press or to answer the rest of the prompts related to ASCII data format. 6. When finished, the screen shows the set- ting you selected: , for example. 7. Dial the telephone number as you usually would. 8. Conduct your conversation in the normal fashion. After the conversation is over, hang up and turn off your TTY. It will auto- mati

On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. A plug and jack used to connect this HA30 / HA40 to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug, RJ11 USOC, is provided with this product. It is designed to be connec

IMPORTANT: Always disconnect HA 30/40 from the telephone before replacing the battery! 2 Installation: 1. Unplug the handset cord from your telephone base. Insert this plug into the jack at the front of the Handset Amplifier. 2. Connect the Handset Amplifier to your telephone base as shown. 3. Pick up the handset. If there is a dial tone, you have installed the Handset Amplifier correctly. Volume Control Adjust the volume to the most comfortable listening level by moving the volume control slide

When AMPLIFY is on, the AMPLIFY indicator comes on. P E0 # HOLD PROG TONE LO HI FLASH REDIAL VOL AMPLIFY * Figure 8 - AMPLIFY Button and Indicator 2. Adjust the volume in the ear piece by moving the VOL slide control in Figure 9. With AMPLIFY on, incoming volume will be up to 48dB louder. Caution: Repeated incremental exposure to amplification levels greater than 18 dB may be harmful to individuals without hearing disabilities. Therefore, do not remove the warning label attached to the back of t