Print mode Batch mode Normal printing (single or multiple sheets) Tear off mode Feeds back media to the tear-off position after printing is completed. Cut mode*1 Prints while cutting at designated sheet units. The following two kinds of cut mode operations are done. • Backfeed • Cut through (Cut through refers to stopping present printing to cut the previous label when it reaches the cut position. After cutting, printing restarts but a gap may be created at the seam of the printing at this time.

printing width: 4.1 in (104 mm) • Max. paper width: 4.65 in (118 mm) • Max. printing length: 32 in (812 mm) Printing speed • 2–4 inches/second in one-inch units Print mode • Batch mode: Normal printing (single or multi sheets) • Peeling mode: Label peeling off the liner after printing • Cut mode: Cutting and printing by the specified number of sheets (label feeding back enabled) • Tear-off mode: Paper feeding back to the printing start position after cutting Bar code generator One-dimensional ba

There is a separate collection systems for used electronics products in accordance with legislation under the WEEE Directive (Directive 2002/96/ EC) and is effective only within European Union. Wenn Sie dieses Produkt entsorgen wollen, dann tun Sie dies bitte nicht zusammen mit dem Haushaltsmüll. Es gibt im Rahmen der WEEE-Direktive innerhalb der Europäischen Union (Direktive 2002/96/EC) gesetzliche Bestimmungen für separate Sammelsysteme für gebrauchte elektronische Geräte und Produkte. Si vo

¦ In case of trouble do not attempt to repair the printer. Ask Citizen Systems service for repair. ¦ Be careful that the printer cover does not entrap your hands or fingers. ¦ Be careful with sharp edges on the printer. Do not allow them to injure you or damage property. •May result in electric shock, burn, or injury. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. DAILY MAINTENA

VDRVDR5V 3.4 Precautions in Installing the Printer The printer must only be operated horizontally. Do not operate vertically or install on a wall. Horizontal position Vertical position CAUTION! DO NOT use the printer under the following conditions. ¦ A state subject to vibration or unstable state. ¦ A state with this product slanted. • Otherwise dropping may cause injury. • Poor print quality may occur. ¦ A state where this product is installed vertically or sidelong. • Malfunction, failure, or

The changed set value is printed. (When change of set value is repeated, the original set value is recovered). When you press the FEED button long, the set value is accepted and then the printer goes to the next setting item. 5. Returning to the memory switch select mode When the setting of the desired content is completed, open the printer cover and then close the printer cover. This allows the printer to print the setting of the changed memory switch. 6. Saving the setting and exiting the memo

Otherwise, burning or injury of hand may result. — 17 — 4.2 Removing Jammed Paper 4.2 Removing Jammed Paper 1. Turn the printer power off. 2. Open the printer cover. 3. Remove the jammed paper including any paper chips remaining. (Remove the paper roll set in the holder as well.) 4. Reinstall the paper roll and close the printer cover. 5. Turn on the printer. The auto cutter mechanism is initialized and the alarm is cleared. CAUTION! ¦ If the cutter blade remains protruded with paper jammed, pre

LVD: EN60950 EMC : EN55022 Class B EN61000-3-2 EN61000-3-3 EN55024 This declaration is applied only for 230V model. CITIZEN is a registered trade mark of Citizen Holdings Co., Japan CITIZEN es una marca registrada de Citizen Holdings Co., Japon Company names and product names in this manual are trademarks or registered trademarks of relevant companies. Copyright c 2008 by CITIZEN SYSTEMS JAPAN CO., LTD. IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not

22 3.5 Partition for 58-mm Wide Paper Roll ......................................... 23 3.6 Long Life Print (LLP) Function Settings ..................................... 24 3.7 Loading Paper .............................................................................. 25 3.8 Attaching the Power Switch Cover ............................................ 26 3.9 Installing the Driver and Utilities................................................26 4. MAINTENANCE AND TROUBLESHOOTING..................

¦ During hexadecimal dump, functions except some command will be disabled. ¦ If print data DOES NOT cover a line, press the FEED button to print the line. When you press the FEED button three times consecutively, or you turn the printer power off, or the printer receives a reset signal from the interface, the hexadecimal dump printing is terminated. Print example HEX DUMP PRINT MODE 1B 21 00 1B 20 04 41 42 43 44 .!.. .ABCD 45 46 47 48 49 4A 4B 4C 4D 4E EFGHIJKLMN 4F 50 0D 0A 31 32 33 0D 0A OP..1