For more information, see the Card Stock & Label Guid available on the Lexmark Web site av • Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height. •Do not load wrinkled, creased, damp, or curled paper. • Flex, fan, and straighten paper before loading it. •Do not use paper that has been cut or trimmed by hand. •Do not mix paper sizes, weights, or types in the same stack. • Store the paper in an appropriate environment. • Do not remove trays while the

Paper tray recommendations • Make sure the paper lies flat in the tray. • Do not remove trays while the printer is printing. • Do not load trays, the multipurpose feeder, or the envelope feeder while the printer is printing. Load them prior to printing, or wait for a prompt to load them. • Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height. • Make sure the guides in the paper trays, multipurpose feeder, or envelope feeder are properly positioned a

Make sure the stack height does not exceed the maximum height indicated by the stack line on the labels in the sources. • Do not load wrinkled, creased, damp, or curled print media. • Flex, fan, and straighten print media before you load it. If jams do occur with print media, try feeding one sheet at a time through the multipurpose feeder. • Do not use print media that you have cut or trimmed yourself. • Do not mix print media sizes, weights, or types in the same print media source. • Make

Note: Do not remove trays while a job prints or while Busx appears on the display. Doing so may cause a jam. 2Squeeze the width guide tab inward as shown, and move the width guide to the correct position for the paper size being loaded. 3Unlock the length guide, squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being loaded. Notes: • Use the size indicators on the bottom of the tray to help position the guides. • For standard paper sizes

By doing so, ink will flow out of the nozzles and has to be dabbed away immediately with a tissue. This trick allows pressing sealed air bubbles out of the nozzle chamber. Should the cartridge print in streaks, please start a cleaning cycle with your printer software. If the problem remains, dab the nozzles with a dampened cloth or leave them to settle in warm water for few minutes. You are facing difficulties refilling your ink cartridges or require more information about the refilling proced

31 | No. 33 | No. 35 | No. 43 Please carefully read these instructions, before starting refilling a cartridge. In order to avoid any soiling, always place a protective mat underneath the cartridge before starting the refilling process, and keep a dampened cloth at hand, to remove any contamination straight away. These instructions apply to the cartridges mentioned above only. The syringe and injection tools as well as the ink must be kept away from children. We shall not be held liable for dama

Place the included blunt needle by screwing it down the tank's opening. Hold the base of the syringe with thumb and forefinger and twist the injecting devise onto it, counter clockwise. First remove the label from the upper side of the cartridge und bore refilling holes. To do so, use the supplied tool to enlarge the 3 existing openings. r m ■ V, w Now insert the syringe inclined into each opening. Slowly and carefully squeeze the ink into each ink chamber, until just under the opening

31 | No. 33 | No. 35 | No. 43 Please carefully read these instructions, before starting refilling a cartridge. In order to avoid any soiling, always place a protective mat underneath the cartridge before starting the refilling process, and keep a dampened cloth at hand, to remove any contamination straight away. These instructions apply to the cartridges mentioned above only. The syringe and injection tools as well as the ink must be kept away from children. We shall not be held liable for dama

© 1999 GBC Pro-Tech Do not duplicate without written permission ARNIN ACHTUNG MISE EN GARDE WARNING ACHTUNG MISE EN GARDE PRO-TECH F-60+™ CAL3200 2 100 90 80 70 60 50 40 30 20 10 1 2 3 4 5 6 7 8 9 10 CAL3200 GBC Pro-Tech 4151 Anderson Road De Forest, Wisconsin 53532 Tel: 608-246-8844 PartNumber930-028 Fax: 608-246-8645 F-60+ Operation and Maintenance Manual The information in this publication is provided for reference and is believed to be accurate and complete. GBC Pro-Tech is not liable for er