Votes - , Average rating:
(
)
)
Manafacture: Citizen
File size: 3.61 mb
File name: f6f45512-1501-4e2d-b5c9-daa927a415d1.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Then press and hold the FEED button. The printer prints the contents of new setting and exits the memory switch setting mode to return to the normal standby state. * Unless saving the setting is executed, the changed setting cannot be enabled. 7. Initializing the memory switch When you want to return the memory switch setting to the initial state, go to “Save To Memory” in the above procedure. Here, open the printer cover and press and hold the FEED button till buzzer sounds. This allows the printer to return to the initial state. * All the memory switches settings are returned to the factory set values. *1: Press for less than 2 seconds *2: Press for more than 2 seconds — 27 — 5.4 Selecting Paper Type *L, *M 5.4 Selecting Paper Type *L, *M Paper type selection is available by the combination of memory switches SW4-4 and SW4-5 by the used of “Memory Switch Select Mode”. In addtion, the following procedure is available. 1 Enter Selecting Paper Type mode. 1)Open the printer cover and remove paper. Pressing and holding the FEED button, turn the printer power ON. The POWER LED starts blinking. 2)Release the FEED button and then close the printer cover. Buzzer sounds and the paper type currently set is indicated by the LED on the operation panel. 2 Select Paper Type. Press the FEED button to match the paper type loaded to the LED indications in the table below. (Refer to the table below.) Green lit (OFF) (OFF) Red lit Green lit Red lit Label Thermal paper roll Black Mark paper POWER LED ERROR LED 3Save the selected Paper Type to the Printer. Open and close the printer cover. By this operation, selected paper type is stored in the printer memory and the Selecting Paper Type mode is terminated. Since then, "P.Length Set" of Memory switch 4-1 becomes disable. When closing the printer cover during the setting a Black Mark paper or label paper in the printer, paper length is measured, and the result will be printed out. * If Paper Detection error occurs at the measurement of paper length, the printer automatically enters Adjusting Paper Sensor mode. Adjust the sensor in accordance with “5-5 Adjusting Paper Sensor”. 5.5 Adjusting Paper Sensor *L, *M Before using Black Mark paper (BM paper) or label, adjust the Paper sensor. First, hold the lever at the upper end of the sensor adjustment control cover located at the left of the Power switch and press the lever down and toward the front to remove the cover from the printer. As shown below, the most left one is a label paper sensor adjuster, the next is Black Mark paper sensor adjuster, and the right one is a level indicator LED. Adjust them in the following procedure. — 28 — Level indicator LED Label paper sensor adjuster *L Black Mark paper sensor adjuster Metal frame Label light receiving sensor *L Black Mark sensor Level indicator LED Label paper sensor adjuster *L Black Mark paper sensor adjuster Metal frame Label light receiving sensor *L Black Mark sensor Label light emitting sensor *L 1 Enter Adjusting Paper Sensor mode. Open the printer cover, remove paper, and then set the printer power switch to ON. Here, POWER LED and ERROR LED go on with the buzzer sound. Then close the printer cover while pressing the FEED button. The ERROR LED starts blinking with the buzzer sound. 2 Set Paper to be adjusted to the Printer. This printer has three types of built-in paper sensors. In case of label, set it so that label is positioned on the label light receiving sensor and label light emitting sensor. In case of Black Mark paper, set it so that the printable portion (other than black mark) is positioned on the Black Mark sensor. With this state kept, closing the printer cover causes ERROR LED to blink with the buzzer sound. 3Adjust Paper Sensor. Turn the corresponding adjuster counterclockwise by using a tapered flat screwdriver. Set the adjuster at the position where LED begins to change from orange to green. Turning the adjuster Green Orange Red counterclockwise * While turning the adjuster by the screwdriver, do not let the part of the screwdriver touch the metal frame. Otherwise proper LED light color will not be displayed while touching. 4Perform Paper Measuring operation When the FEED button is pressed, label is fed and paper measuring is carried.If the FEED button is presed during the paper measuring, the result will be printed out as follows, and the printer memory switch will be initialized. * The measuring result is a reference value Label Length : XXXmm Gap Length : XXmm Black mark Interval : XXXmm Black mark Length : XXmm showing a label length showing a gap between labels showing a black mark pitch showing a black mark height < Example of label measuring result*L > < Example of black mark paper measuring result *M> — 29 — 5.6 Full cutting label paper *L 5.6 Full cutting label paper *L When full-cutting the label paper with the printer installed horizontally,Be sure that the guide plate is mounted on the paper exit of the printer cover. (This guide plate was set t...
Other models in this manual:Printers - CT-S4000M (3.61 mb)