Votes - 5, Average rating: 3.8
(
)
)
|
manual abstract
A shortcut to “CallList” is established n = Number of missed calls. 2) Not used. 3) Only used when option unit is connected. 4) Only shown when pre-defined WAP portal is available. 5) Only available to your system administrator. Home. Return to home position (idle mode). BusinessPhone – Ericsson Dialog 4425 IP Vision 17 Description Dial tone (System ready to accept digits) Special dial tone (System ready to accept digits, active diversion on telephone) Ringing tone (Ringing signal to called party) Busy tone (Called party is busy) Number unobtainable tone (Called number not accessible or vacant) Call Waiting tone Congestion tone (Call cannot be executed due to congestion or called party blocked) Verification tone (Verification that ordered function is accessed) Intrusion tone (Sent to all parties during Intrusion) Internal ringing signal External ringing signal Automatic Callback signal Tones & Signals Tones are audible in the handset. -repeated after 4 s Ringing signals are emitted from the phone. - repeated after 4 s - repeated after 4 s Note: The tones and ringing signals in this guide refer to the standard system but may vary between countries. 18 BusinessPhone – Ericsson Dialog 4425 IP Vision Start the Phone – Log On/Off Start the Phone – Log On/Off All system settings for your IP phone must be set by the system administrator before you can use the phone. Connect the required cables. See section “Installation” on page 132. Note: Depending on the settings in your network and telephone system, the start up procedure may be different from phone to phone. Check the display on your phone and read the required sections in this chapter to continue with the start up procedure. When this is done, and the phone is connected to the local network (LAN), your phone starts the start-up procedure automatically when connected to the mains. Notes: The phone does not work during a power failure. After a power failure the phone will restart automatically. However, when a password is requested, you must log on before the phone can be used again. Reset the phone If your phone does not work properly, you can use the following procedure to reset the phone. This procedure will also clear the Call list. After the procedure you must log on again to use the phone. iE# Press simultaneously for at least one second to reset the phone. BusinessPhone – Ericsson Dialog 4425 IP Vision 19 Start the Phone – Log On/Off Start the Phone Connect the phone to the local network. See the Installation section, “Install cables” on page 135. If an external power adapter is used: Connect the adapter to the mains and connect the plug from the adapter to “POWER” on the underside of your phone. See the Installation section, “Install cables” on page 135. After a few seconds the Headset key lamp will light for about five seconds, then the displays shows: Settings CallList Contacts ? User administrator mode to change IP settings (x) (No change) The x indicates a timer counting down seconds. If no key is pressed during this time, “no change” is selected automatically. Notes: The administrator mode is used to change the IP settings of the phone. All administrator mode changes should be done by your system administrator. If you want to use the previously stored settings, you can speed up the procedure by pressing the Loudspeaker key. Now the display informs you that the phone is connecting to the server and that the software is loading. This takes about 15 seconds. After a self-test, the phone is ready for log on. 20 BusinessPhone – Ericsson Dialog 4425 IP Vision Start the Phone – Log On/Off LAN access control (network authentication) (Dialog 4425 v. 2 phone only). Your telephone might require a network authentication to gain access to the network. In this case you must enter a valid user identity and password. Note: The user identity and password used for the network authentication is not the same user identity and password you use to log on. The password is obtained from, and can only be changed by the system administrator. Settings CallList Contacts ? User administrator mode to change IP settings (x) (No change) z Enter your user identity. (The display menu key Erase, is used to remove a wrong entry.) Log on Press (see display). z Enter your password. (The display menu key Erase, is used to remove a wrong entry.) Note: The password can be entered with letters or numbers, see section “Write Text” on page 90. Log on Press (see display). If your user identity and password are accepted, the phone continues with the startup procedure. Note: If your user identity and password are not accepted, contact your system administrator. BusinessPhone – Ericsson Dialog 4425 IP Vision 21 Start the Phone – Log On/Off Continued startup procedure The display shows: Settings CallList Contacts ? User administrator mode to change IP settings (x) (No change) A timer counts down from 5 seconds. If no key is pressed during this time, (No change) is selected automatically. Notes: Y...
Other models in this manual:Phones - IP Vision Dialog 4425 (1.01 mb)