Votes - 3, Average rating: 4.3 ( )

Manafacture: Citizen File size: 3.61 mb File name: Language of manual:

*58 mm is only for label supporting model. 4. Change the setting of paper width by reffering to the section 5.2, "Manual Setting of Memory Switch". Partition Partition Scales 3.6 Setting DIP Switch CAUTION! When using 112 paper roll, the partition is not used. 3.5 Partition for Paper Roll At the time of shipment, this partition is not installed. 1. Confirm that the power switch is OFF. 2. Open the printer cover. 3. Insert the partition into the slot and align it with the scale inside of the printer which meets the width of the paper roll used. When using the 80mm or 82.5mm wide paper roll, set the partition by using the accessory screw. *58 mm is only for label supporting model. 4. Change the setting of paper width by reffering to the section 5.2, "Manual Setting of Memory Switch". Partition Partition Scales The DIP switch is present on the serial Interface board interface board. mounting screws The function of each switch is as shown below. CAUTION! DIP switch ¦ As for the setting of the serial interface, it gives priority to the setting of the memory switch rather than the DIP switch as the factory default. ¦ Consult with the dealer where the printer was purchased when the change of the DIP switch setting is necessary. Switch No. Function ON OFF InitialSettings 1 Communication condition setting method DIP switch setting Memory switch setting OFF 2 Hand shake XON/XOFF DTR/DSR OFF 3 Bit length 7 bits 8 bits OFF 4 Parity check With parity None OFF 5 Parity selection Even parity Odd parity OFF 6 Baud rate selection See Table below. OFF 7 ON 8 INIT Reset Invalid OFF Selecting baud rate Baud Rate (bps) Switch No. 6 7 2400 OFF OFF 4800 ON OFF 9600 OFF ON 19200 ON ON 38400, 57600 and 115200 bps can also be selected by a command, etc. — 15 — 3.7 Adjusting the Paper Near-end Sensor 3.7 Adjusting the Paper Near-end Sensor 1. Lightly push in the paper near-end sensor unit. 2. Move the paper near-end sensor unit to the right and left while keeping to press it. The position to be set varies in accordance with the setting of the printer, horizontal or vertical, or diameter of the paper roll as shown in the following figure. Sensor Position Roll paper diameter at the detection of near-end Outer core diameter of roll paper used Horizontal **1 .21.0 .18.0 *2 .24.5 .21.5 3 .28.0 .25.5 4 .31.5 .28.0 5 .35.0 .32.0 Vertical 5 .21.0 .18.0 4 .24.5 .21.5 3 .28.0 .25.5 2 .31.5 .28.0 1 .35.0 .32.0 * Factory setting for USA version ** Factory setting for other country version CAUTION! ¦ Paper remaining differs by the type of paper roll used. ¦ The external diameter of the paper roll is only for reference. ¦ When a paper end error is detected incorrectly during using a paper roll with a honeycomb type core, move the sensor position to the larger number. 21345 Paper-near-end sensor unit — 16 — 4. MAINTENANCE AND TROUBLESHOOTING 4.1 Setting/Replacing the paper roll 1. Pull the cover open button forward. 2. Open the printer cover. 3. Insert a paper roll with its print area facing down as shown in the figure and pull out the paper end straightforward several cm (or inches) out of the printer. 4. Firmly close the printer cover until a click can be heard. See 5.3 Manual Setting of Memory Switch CAUTION! ¦ Always use the specified types of paper roll. ¦ Confirm that the paper roll is set correctly. ¦ When the paper is skewed and not extended straightforward from under the printer cover, open the printer cover and adjust the paper correctly. ¦ When the printer cover is opened after setting the paper, be sure to pull the paper straightforward several cm (or inches) out of the printer, and then close the printer cover. ¦ When closing the printer cover, press on the center part of the cover to close it firmly. ¦ When setting paper, be careful not to have your finger injured by the manual cutter or paper edge. ¦ In the case of selecting "Valid" with memory SW4-3, the paper is fed and cut automatically when the printer cover is closed. WARNING When opening the printer cover, DO NOT touch the print head or cutter blade. Otherwise, burning or injury of hand may result. 4.2 Removing Jammed Paper 1. Turn the printer power off. 2. Open the printer cover. If the cutter blade remains protruded with paper jammed, do not force the printer cover to open. Referring to the section 4.7, restore the blade to the normal position and then open the cover. 3. Remove the jammed paper including any remaining paper shreds. 4. Turn on the printer. The auto cutter mechanism is initialized and the alarm is cleared. CAUTION! ¦ If the cutter blade remains protruded with paper jammed, DO NOT open the printer cover foribly and try to turn OFF and ON the printer power. If the cutter blade cannot be restored, refer to the section 4.7. ¦ The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touch the heating element of the head with a bare hand or metal object either. — 17 — 4.3 Periodic cleaning 4.3 Periodic cleaning If the print head or pla...

Download now

Please, enter two numbers from picture: