Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
FT-800 SERIES DISHWASHER FOOD EQUIPMENT • Water and energy saving design through reduced water and tank heat usage and automatic pump shut down control through conveyor. • Common water, drain, electric and steam connections. • Exclusive load end flush system. • Built-in integral wiring channel. • Automatic temperature control and positive low-water heater and pump seal protection. • Built-in inherent motor overload protection with manual reset. • Built-in vent ducts—dampers and drip control. • Improved washability with high pressure prewash—wash and power rinse systems. • Compct modular design. • 115 volt pilot circuit. • Lower prewash arm. • Automatic initial fill. FT-800 SERIES DISHWASHER WITH ELECTROMECHANICAL CONTROLS OUTSTANDING STANDARD FEATURES • Energy saving low water consumption design—5.7 GPM Hot Water (180°F); 3.9 GPM Low Temp (140°F). • Stainless steel construction including frame, legs, feet, drain piping, wash arms. • Electro-mechanical controls in top mounted stainless steel control center. • 36" Load/Unload height. • Energy efficient convertible hot water or low temp/chemical sanitizing. • Door actuated drain closers. • Sealed dial type thermometers for wash—power rinse—final rinse—temperature indication. • Wash arms easily installed and removed without tools. • All function components (motors, drains, etc.) located on operators side of dish- machine for accessibility and ease of maintenance. • Built-in integral prewash water replenishment system. • Final rinse actuator. • Removable self-flushing stainless steel strainer pans and large deep scrap buckets for each tank. • Door interlocks on all doors. • Optional energy saving blower- dryer. Electric 20 KW—63% energy reduction. Steam 75 lbs./hr.—56% energy reduction. • Choice of electric, steam injection or steam coil heat. Specifications, Details, Dimensions and Connections inside. FT-800 SERIES DISHWASHER FT-800 SERIES DISHWASHER STANDARD DESIGN FEATURES TOP MOUNTED CONTROL PANEL – Controls in top-mounted stainless steel control center with master On/Off Power Switch. WASH ARMS – Computer-designed prewash, wash and power rinse arms. Arms designed so they can be installed only in correct position. STOP/START PUSH BUTTONS – Recessed, side located waterproof Start/Stop push buttons and flip-up hinged dishware platform on both ends of dishwasher. FLUSH DOWN – Exclusive load end flush down system. DRAIN CLOSERS – Door operated drain closers . . . front located drains, stainless steel tank overflow tubing to prewash, and final rinse water feed piping. PUMP – Self-draining Hobart pump motors with inherent motor protection and manual overload reset push buttons on each motor. FT-800 SERIES DISHWASHER FT-800 SERIES DISHWASHER WIRING CHANNEL – Built-in integral wireway above tank water level. SCRAP PANS – Large one-piece sloped scrap screens and deep removable recessed scrap buckets for prewash, wash and power rinse tanks. VENT DUCTS – Built-in vent ducts with adjustable dampers and drip shield on each end of dishwasher. 2" x 24" load end and 4" x 24" discharge end (inside dimensions). POSITIVE LOW WATER PROTECTION – Solid state positive low water protection for tank heaters. FT-800 SERIES DISHWASHER FT-800 SERIES DISHWASHER DETAILS, DIMENSIONS AND CONNECTIONS RIGHT TO LEFT OPERATION FT-800 SERIES DISHWASHER FT-800 SERIES DISHWASHER R 701 RIDGE AVENUE TROY, OHIO 45374-0001 FT-800 SERIES DISHWASHER FT-800 SERIES DISHWASHER DETAILS, DIMENSIONS AND CONNECTIONS LEFT TO RIGHT OPERATION FT-800 SERIES DISHWASHER FT-800 SERIES DISHWASHER 701 RIDGE AVENUE TROY, OHIO 45374-0001 R FT-800 SERIES DISHWASHER FOOD EQUIPMENT FT-800 SERIES DISHWASHER FOOD EQUIPMENT SPECIFICATIONS Listed by Underwriters Laboratories Inc. and National Sanitation Foundation. Meets Requirements of A.S.S.E. Standard No. 1004. DESIGN:Fully automatic, flight-type dishwasher machine, consisting of a 5' x 7' loading section with power recirculating prewash, an 8' power wash, power rinse and fresh water final rinse section, and a 5', 7', 9' or 11' drying and unloading section. Recirculating water prewash, power wash, power rinse, and final rinse compartments constructed with splash baffles and flexible plastic strip curtains for effective control and separation of spray systems. Specify high or low temperature operation. CONSTRUCTION: Tank and chambers are heavy gauge stainless steel with No. 3 polish on appearance surfaces. Stainless steel frames, legs, and feet are standard. Three large inspection doors with welded handles. PUMPS: Recirculating pumps with Ni-Resist impellers and face seal with stainless steel metal parts and ceramic seat. Readily removable motor-impeller assembly permits quick inspection. All pumps are self-draining. MOTORS: Hobart-built, grease-packed ball bearings, splashproof design, ventilated with inherent overload protection in each motor. Recirculating prewash unit 2 H.P., power wash and power rinse 3 H.P. each, conveyor 1.2 H.P. Available in electrical specifications...