To select Special Peak mode, press and hold then press . While in this mode the Peak flag will flash. Note: While tracing cables in any mode, keep the Receiver handle in line with the suspected cable path. See section Initial Receiver Configuration (Page 3) to set the power frequency to 50 Hz or 60 Hz. The Receiver can be tuned to locate 3 different harmonics of the chosen power frequency. H50 Hz or H60 Hz (high harmonic): Best for general locating of passive power. L50 Hz or L60 Hz (low harmoni

When the voltage magnitude is sufficient to impair the accuracy of the ohms measurement, only voltage will be displayed. If the voltage is AC, a sine wave will be visible on the display. If a high AC voltage is detected, a rapid beeping tone will be heard. Page 6 Press to select Trace mode. Press again to select one or all of the four frequencies. The display will alternate between displaying the selected frequency and the output signal current. It is best to choose the lowest frequency for dire

Press only when a marker is detected and the signal is too strong. To search for a new marker, reset the Receiver gain to the initial setting by turning its power OFF and back ON, or pressing and then re-selecting the Peak mode. Refer the EMS Marker Locating Accessory operating instructions for further information. Page 17 TONING AERIAL FAULTS Transmitter Setup Perform a battery test; then with the Transmitter off, plug the direct connect cable into the front panel jack. If fault is a shorted pa

Philips shall be under no liability forany injury, orany loss ordamage caused to property or products other than the product under guarantee. This guarantee does not prejudice your rights under common law and statute, and is in addition to the normal responsibilities of the retailer and Philips. Howto claim. Should your Philips product fail within the guarantee period, please return it to the retailerfrom whom it was purchased. In most cases the retailer will be able to satisfactorily repair

Cet appareil vous donnera encore plus de satisfaction si l’utilisation et l'entretien sont suivis selon le mode d'emploi. Malgré tous les soins apportés, l'apparition de défauts n'est pas exclue. Dans ce cas, nous vous senons reconnaissants de bien vouloir vous adresser directement chez votre vendeui muni du passeport de l'appareil ainsi que de la facture s'y reportant_ 6ARANZIA PER LA SV1ZZERA Gli apparecchi Philips sono prodotti con materiali di prima qualité e assembîati con la massima cura

Make certain that the projection at the back of the assembly is fully seated in the cartridge body first (Fig. 9a), and that the assembly “clicks” up into place, with no gap between its top edge and the front of the black plastic tone arm head (Fig. 9b). Replace the stylus after 400 hours of use. To maintain original performance, insist upon a genuine Audio-Technica brand replacement stylus. Look for the Audio-Technica trademark ( ) on the front of the stylus assembly and on the packaging. Figur

8 BASIC OPERATIONS SELECTION OF AUDIO/VIDEO SOURCE ......................... 9 RECORDING AN AUDIO SOURCE ................................. 10 RADIO RECEPTION MANUAL TUNING ............................................................. 11 DIRECT TUNING ............................................................... 11 PRESETTING STATIONS ................................................. 12 DOLBY SURROUND SELECTING DOLBY PRO LOGIC ................................... 13 ADJUSTING SPEAKER LEVEL BALAN

@ Front speakers @ Center speaker Position inthecenter of thetwo front speakers. In addition, position on or below the TV set, if connecting a TV set to the unit. @ Surround speakers Place the surround speakers directly to the side of or slightly behind the listening area. Align them horizontally, about 1 meter (3,2 feet) above ear height. @ Sub woofer Place the sub woofer in any place between the two front speakers. m Sound from the surround speakers or center speaker depends on the setting of

Operation is possible after four seconds. The VOL (volume) level or function name is displayed one after the other for the first four seconds. The selected function indicator lights up in red. To change the brightness level of the display 1 Press the ECO button repeatedly until “DIM MODE” is displayed. 2 Within 4 seconds, press the ENTER button. 3 Within 4 seconds, turn the MULTI JOG to select the dimmer mode as below. The mode will be automatically set after 4 seconds. It will also be set if th

To adjust the sound level of the connected source The input sensitivity level of each function can be adjusted (except the TUNER, CD(DIGITAL), VIDEO 1 (DIGITAL), VIDEO 2 (DIGITAL) and VIDEO 3 (DIGITAL) functions). When the sound level of the connected source is higher or lower than that of the TUNER, adjust it as follows. 1 Select the function to be adjusted. Turn the FUNCTION or press the TAPE MONITOR button and play the source. 2 Press the N(UP) or M(DOWN) button repeatedly. Adjust the level s