• Use only cleaning fluids specifically recom- mended for high pressure washers. Follow manufacturers recommendations. Do not use chlorine bleach or any other corrosive compound. • Some cleaning fluids contain substances which could cause injury to skin, eyes, or lungs. HAZARD RISK TO FLUID INJECTION HOW TO PREVENT IT WHAT CAN HAPPEN • Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury.

READ AND SAVE THESE INSTRUCTIONS HAZARD RISK OF EXPLOSION OR FIRE HOW TO PREVENT IT WHAT CAN HAPPEN • Spilled gasoline and it’s vapors can become ignited from cigarette sparks, electrical arcing, exhaust gases, and hot engine components such as the muffler. • Shut off engine and allow it to cool before adding fuel to the tank. • Use care in filling tank to avoid spilling fuel. Move pressure washer away from fueling area before starting engine. • Heat will expand fuel in the tank which could resu

NOTE: Using a pump protector/ winterizer or *RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. PRESSURE WASHER 1. Drain all water from high pressure hose. 2. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun holder. 3. Store chemical hose so it is protected from damage. 1. Obtain a funnel, six ounces of *RV antifreeze, and 16

electrical arcing, exhaust gases, and hot • Use care in filling tank to avoid spilling fuel. engine components such as the muffler. Move pressure washer away from fueling area before starting engine. • Heat will expand fuel in the tank which • Keep maximum fuel level ." below top of could result in spillage and possible fire tank to allow for expansion. explosion. • Operating the pressure washer in an ex• Operate and fuel equipment in well ventiplosive environment could result in a fire. lated a

RISK TO BREATHING (ASPHYXIATION) WHAT CAN HAPPEN HOW TO PREVENT IT • Some clean ing fluids con tain substanc es which could cause injury to skin, eyes or lungs. • Use only clean ing fluids spe cif i cal ly rec om mend ed for high-pressure washers. Fol low manufacturers recommendations. Do not use chlorine bleach or any other corrosive compound. A17914 2- ENG RISK OF FLUID INJECTION AND LACERATION WHAT CAN HAPPEN • Your pressure washer operates at fluid pressures and velocities high enough to pen

If water has frozen in the pressure washer, thaw the pressure washer in a warm room before starting. DO NOT pour hot water on or into the pump; internal parts will be damaged. 1. Check engine oil levels. Add oil as necessary. 2. Check fuel level. Add unleaded gasoline (rated 86 octane or higher) as required DO NOT refuel a hot engine. Refueling a hot engine could cause a fire. Use only fresh, clean regular or unleaded gasoline. Close the fuel shutoff valve during refueling. 3. Attach a garden ho

To depressurize, turn engine/motor off, turn water supply off and squeeze gun trigger 2-3 times. 5. After each use, wipe all surfaces of the pressure washer with a clean, damp cloth. • Do not store the pressure washer outdoors. • Do not store the pressure washer where it might freeze unless it has been properly winterized. 9. Storage LONG TERM STORAGE INSTRUCTIONS (MORE THAN 30 DAYS IN STORAGE) 1. Remove fuel from the tank and run the pressure washer in a normal operating mode until the engine s

Slide the handle assembly over the lower legs of the cart base. Use the (supplied) star knob and bolts to secure the handle to the legs (See Figure 9). 2. Slide clear plastic detergent hose onto brass hose barb (See Figure 10). 3. Insert quick connect spray tips into rubber holders on front of the placard. (See Figure 11). 4. Secure garden hose (not included) to the inlet connection on pump (See Figure 12). 5. Connect the high pressure hose to the pump outlet (See Figure 13). 6. Attach the lance

GFCI has tripped 1. Push reset button on plug start up 2. Plug is not well connected or electric 2. Check plug, socket and fuses socket is faulty 3. Extension cord too long or wire size 3. Remove extension cord too small 4. Main voltage supply too low 4. Check that main supply voltage is adequate 5. Thermal safety switch has tripped 5. Switch off unit and allow motor to cool down Motor stops suddenly 1. Extension cord too long or wire size 1. Remove extension cord too small 2. Thermal safety swi

It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Frequently Asked Questions Why don’t I have any water pressure? • Is the water hose attached to the pressure washer? • Is the water turned on? • Check for any kinks, leaks, or blockage in the hoses, fittings, or the nozzle. • Is the quick connect tip in place? (See Page 10). • Is the inlet filter screen free of debris? Check and remove deb