See How To Use Wand instructions in this section. DO NOT STOP SPRAY ING WATER FOR MORE THAN TWO MINUTES AT A TIME. PUMP OPERATES IN BYPASS MODE WHEN SPRAY GUN TRIGGER IS NOT PRESSED. IF PUMP IS LEFT IN BYPASS MODE FOR MORE THAN TWO MINUTES INTERNAL COMPONENTS OF THE PUMP CAN BE DAMAGED. WHEN USING THE HIGH PRESSURE SETTING, DO NOT ALLOW THE HIGH PRESSURE SPRAY TO COME IN CONTACT WITH UNPROTECTED SKIN, EYES, OR WITH ANY PETS OR ANIMALS. SERIOUS INJURY CAN OCCUR. 12 — ENG D22885 3. Turn water sour

This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these sections. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,may res

• If repair or service part purchase is required, our many Authorized Warranty Service Centers are conveniently located and equipped to handle all in-warranty and out-ofwarranty service. • For the location of the nearest Authorized Warranty Service Center call 1-888-559-8550, 24 hours a day, 7 days a week or visit our web site @ • All pressure washers carry a manufacturer's one year warranty from date of purchase for consumer use and a 90 day warranty for commercial use. • Retain sales receipt a

Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See Nozzle Cleaning instructions in the Maintenance section. Remove and clean filter. Water filter screen clogged. Check with Authorized Warranty Service Center (AWSC.) Defective E-Z start valve. Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re-connect wat

Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine manual for correct procedure. 2. Check engine oil level. See Engine Operators Manual for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 3. Verify the filter screen is in water inlet of pump. NOTE: Cone side faces out. 4. Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons per minute at 20 p.s.i. 5. Connect high pressure hose t

. For the location of the nearest Authorized Warranty Service Center call 1-888-559-8550, Ext. 2, 24 hours a day, 7 days a week or visit our web site @ devap.com. . All pressure washers carry a manufacturer's one year warranty from date of purchase for consumer use and a 90 day warranty for commercial use. . Retain sales receipt as proof of purchase for warranty service. 5 — ENG D22885 BOX CONTENTS Handle Engine Manual Engine Frame and Wheel High Pressure Hose Assembly Bagged Handle Chemical Hos

2. Change to a wider spray pattern nozzle. See How to Use Wand paragraph in this section. 3. Reduce the speed of the gasoline engine (RPM). Slow the engine down and the water pressure will go down with it. 9- ENG D25805 TO USE WAND Your pressure washer is equipped with four spray nozzles. Each nozzle is color coded and delivers a specific spray pattern for a particular cleaning purpose. The size of the nozzle determines the size of the fan spray and the pressure out of the nozzle. The 0., 15. ,

electrical arcing, exhaust gases, and hot • Use care in filling tank to avoid spilling fuel. engine components such as the muffler. Move pressure washer away from fueling area before starting engine. • Heat will expand fuel in the tank which • Keep maximum fuel level ." below top of could result in spillage and possible fire tank to allow for expansion. explosion. • Operating the pressure washer in an ex• Operate and fuel equipment in well ventiplosive environment could result in a fire. lated a

NOTE: Chemicals and soap will not siphon when wand is in the high pressure setting. Barbed Fitting READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT When using the high pressure setting, DO NOT allow the high pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury can occur. Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks c

2. Disconnect spark plug wire. 3. Pull trigger on gun handle to relieve any water pressure. 4. Disconnect the wand from the gun. 5. Remove the nozzle from the end of the wand with the 2mm allen wrench provided as shown. 6. Clean the nozzle using the nozzle cleaner provided or a straightened paper clip. Insert into the nozzle end and work back and forth until obstruction is removed. 8. Reassemble the nozzle to the wand. Tighten securely to prevent leaks. 9. Reconnect wand to gun and turn on water