Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left si

(RSC-1650H and RSC-1650HR). Control Buttons 1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1650H and RSC-1650HR) 2. SPEED DISPLAY: Display’s current Speed. 3. TEMPERATURE BUTTON- (RSC-1650H and RSC-1650HR): To change the temperature (max. RSC-1650H: 122°F, 50°C/RSC-1650HR: 266°F, 130°C)ofthe upper roller, press up or down arrow button. 4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the up or down arrow button. 5. RUN: To start the

(Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bott

To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at 1-800-397-1025. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating machine. Keep this information for future reference. Failure to comply any of t

There might be the possibility for difference to the above numbers due to the change of voltage or adjustment of tension. 2. COLD LAMINATING 1. Put cold roll film on upper bar.(Set the same as methord of HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. - 2

2. FUNCTIONS OF BUTTONS : Upper roller temperature controller : Lower roller temperature controller UPPER SPEED LOWER UPPER SPEED- 14 - : Speed controller : Choose memorized working condition : . Increase temperature . Increase speed . Restore the memorized working setting : . Decrease temperature . Decrease speed . Restore the memorized working setting : Cold and Hot mode change : Check current temperature : Saving electricity while the machine is not being operated. : Reverse function Stay pre

(Note :Turn the fastening nut of the Emergency switch counterclockwise and disaasemble the Emergency switch before disassembling the Right cover.) 2. Disassemble the Rear cover. 3. Disassemble the power switch bracket which is located at the left side of the machine. M5 screw 6EA Power switch bracket Plate-Rewinder L 4. Put the Plate-Rewinder L on the outer side of the frame as shown in the following figure and fasten it with six M5 screws. 5. Put the Plate-Rewinder R on the outer side of the fr

7. Turn off the power when unattended or not in use. Unplug machine before movig it or when it is not in use for an extended period of time. 8. This machine is intended for indoor use only. 9. Do not alter or extend electric plug. Plug is configured for appropriate electrical supply. 10. The socket-outlet shall be installed mear the equipment and shall be easily accessible. - 3 CHARACTERISTICS RS Roll Laminator Line are advanced laminators with time transcendental design, utilizing the latest in