Votes - 4, Average rating: 4.5 ( )

Manafacture: Royal Sovereign File size: 1.41 mb File name: Language of manual:

There might be the possibility for difference to the above numbers due to the change of voltage or adjustment of tension. 2. COLD LAMINATING 1. Put cold roll film on upper bar.(Set the same as methord of HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. - 21 4. After pressing the button choose and set proper speed by using the and button. 5. It is when ready is show on the screen and the buzzer rings three times. sound three times. 6. Turn on the take up device and set the proper film tension by pressing the button. Lower tension would make better operation. 7. Set document on the table. You should allow at least 5mm(1/4”) space on each side for perfect laminations 8. Turn the switch “Run” and “take up motor” at the same time. The liner and film will be rolled at the same time. 9. When lamination is finished, press the button. For your convenience, it would be better to set table guide in proper position. And if needed, cut documents with cross cutter. 10. Set pressure lever at the Hard board/15mm mode. 11. Turn off the power switch. 1. Set up the protection paper. Otherwise, glue form the film will be stuck on the face of roller and it can be seriously damaged. 2. Turn the switch “Run” and “Take up motor” at the same time. 3. For worm lamination, set temperature from the hot mode. 1. It is convenient to use the remote control in the back of machine while laminating. 2. It is also convenient if you use Foot Switch while laminating HARD BOARD. 3. "RUN", "STOP", "REV" buttons on Remote Control have same functions with the ones on Control Panel. TIPS FOR REMOTE CONTROL AND FOOT SWITCH *** Reference *** C/HOT RUN STOP SPEED - 22 - 4. Press Foot Switch one time for "RUN", press one more time for "STOP". (Don't keep pressing) 5. After use of Remote Control, attach it to the left side of rear of machine METHOD FOR USING CUTTER **Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/3 of the width of lamination 3. Grasp film with one hand and press the cutter cutter downward and slide it to the direction intending to cut with another hand. 4.Press the cutter and slide it the other way. IMPORTANT SAFETY CONCERNS 1.Please be cautious that neck tie, necklace, long hair, clothes are kept well away while operation. 2. Prevent children from accessing the machine - 23 Extreme Heat Will Cause Injury 3.Place the machines on the plated place so that 4.Make certain that the machine is connecterd to an adequate power souce. 5.Do not use any other purposes other than Lamination. MAINTENANCE 1.Do not allow the machine to run with only one roll of film installed. The melted resin will adhere to one roller and ruin future laminations. 2.The width of film should be bigger than the material, and Width of upper side and lower side of film should be same in order not to allow melted resin to adhere to the rollers. 3.Be sure to adjust the film tension while in operation. If the tension is too tight, it could cause the film to stretch. 4.After work, you should clean the resin from the rollers before beginning the next operation. 5.Please check the lubricant after long operation or you do not use for a long time. 6.Check the chain linking each gear is not loosened. The limit tension allowed is 3mm. Symptom Cause Check point *Rollers do not operate 1. Power cord may not be plugged 1. Check the power cord after press RUN button in. 2. Check the switch is on 2. Power switch is at OFF mode. 3. Check the emergency switch 3. Emergency switch may be at is off ON mode. 4. Release STND-BY switch by It's not out of order - 24 4. It may stay at STAND-BY mode. press the STND-BY button *Hot roller is not heater up. 1. It is set at the cold mode 2. Memorized temp may be lower than atmosphere temp. 1. Change the function to hot lamination. 2. Set proper temperature for the work *Wrinkled lamination result1. Film tension is not proper, too tight. 1. Adjust film tension. *Result of lamination is not clear1. Temperature on the hot roller is too low or lamination is too speedy. 1. Increase the temperature on the hot roller or decrease the speed. SPARE PARTS PART NAME EA MODEL PART NAME EA MODEL Core(76mm) 6 RSH-1650 RSH-1050 RSR-1050 RSR-685 Bolt(M8X65) 8 RSH-1650 RSH-1050 RSR-1050 RSR-685 Washer(.8) 8FUSE(50T) (AC250V 6.3A) 1 Nut(M8) 4FUSE(65TS) (AC250V 20A) 1 L-Wrench 1 WARRANTY 1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized service center will repair this product free of charge if it is defective in material or workmanship. 2. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or improper installation, operation or external scratch, any damage caused from servic...

Download now

Please, enter two numbers from picture: