Votes - 5, Average rating: 4.4 ( )

Manafacture: United States Stove File size: 413.2 kb File name: Language of manual:

Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fibers. PROPER INSTALLATION SEQUENCE: 1. Install the rear log (#2) on the rear set of locators. Visually check to verify the log is securely placed on the locators. 2. Install the front log (#1) on the front locators. Visually check to verify the log is securely placed on the locators. 3. Install the left and right cross twigs as illustrated, on the locator pins provided in the front and rear logs. Holes provided in the bottom of the cross twigs should allow them to seat completely over these pins. FIG 2A FIG 2B FIG 2C 1) Lift the front screen slightly up (Fig. 2A) and then tilt the bottom of the screen inward and downward (Fig. 2B). 2) Lean the top of the screen toward you slightly (Fig. 2B) and then proceed to carefully bring the screen straight back (Fig. 2C). NOTE: To reinstall the front screen, reverse steps 1 & 2. LOG ASSEMBLY OPERATING INSTRUCTIONS Avoid any drafts that alter the burner flame patterns. Do not allow fans to blow directly into the heater. Do not place a blower inside burn area of firebox. Ceiling fans may create drafts that alter burner flame patterns. Sooting and improper burning will occur. This vent-free gas heater is intended to be smokeless. If logs appear to smoke, turn off the heater and call a qualified service person. Initial burn off may cause slight smoke and odor during the first four hours of operation. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.WARNING A. This appliance is equipped with an ignition device (piezo) which automatically lights the pilot. If piezo fails, then light the pilot using matches. Refer to match lighting instructions (page 13). When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not attempt to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 11 OPERATING INSTRUCTIONS LIGHTING INSTRUCTIONS 1. STOP! Read the safety information on the previous page. 2. Turn off all electrical power and open the access door. 3. Turn off the rear burner and set the front burner to low. 4. Push in gas control (knob 1) slightly and turn clockwise to "OFF". KNOB 3 3. REAR BURNER OFF IGNPILOT ON OFF ONMAX MINMeritikMAXITROL KNOB 11. PILOT 2. FRONT BURNER KNOB 2 NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force. 5. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow "B" in the safety information on the previous page. If you don't smell gas, go on to the next step. PILOT LOCATION TOP VIEW OF BURNER ASSEMBLY 6. Push in the control (knob 1) all the way and rotate counter-clockwise to "PILOT". The piezo ignitor will light the pilot as the knob passes "IGN" traveling to the "PILOT". Con tinue to hold the control (knob 1) in for about ten (10) seconds after the pilot is lit. Release knob and it should pop back up. Pilot should remain lit. If it goes out, repeat steps 4 through 6. If the control (knob 1) does not pop up when released, stop and immediately call your ser vice technician or gas supplier. If the pilot will not stay lit after several tries, turn the gas control (knob 1) to "OFF" and call your service technician or your gas supplier. 7. Turn gas control (knob1) counter-clockwise to "ON". 8. Set the front burner (knob 2) to the desired setting rotating counter-clockwise to MAX. and clockwise to MIN. 9. Set the rear burner (knob 3) to the desired setting rotating counter-clockwise to MAX./ ON or MIN. 10. Close access door and turn on electrical power. TURN OFF GAS TO APPLIANCE 1. Open access door. 2. Set front burner to Min. and turn off the rear burner by depressing knob and rotating clockwise until stop. 3. Unpl...

Download now

Please, enter two numbers from picture: