Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Accidental acceleration of the engine can cause the chain to rotate and cause serious injuries. Warning! Always switch off the engine and fit the scabbard over the cutting attachment before transporting the power tool over long distances. When transporting it in a vehicle, properly secure it to prevent turnover, fuel spillage and damage to the unit. Fuel Your STIHL power tool uses an oil- gasoline mixture for fuel (see the chapter on "Fuel" of your instruction manual). Warning! Gasoline is an extremely flammable fuel. If spilled and ignited by a spark or other ignition source, it can cause fire and seri ous burn injury or rning! the power tool. Note that combustible fuel vapor may escape from the fuel system. g Instructions Fu propewhent not smoke or bring any fire or flame near andling gasoline or fuel mix. Do damage. Use extreme caution To reduce the risk of serious injury from burns, never attempt to refuel the unit until it has been completely removed from the operator. Warning! Fuel your power tool in well-ventilated areas, outdoors. Always shut off the engine and allow it to cool before refueling. Gasoline vapor pressure may build up inside the fuel tank depending on the fuel used, the weather conditions and the tank venting system. In order to reduce the risk of burns and other personal injury from escaping gas vapor and fumes, remove the fuel filler cap on your power tool carefully so as to allow any pressure build-up in the tank to release slowly. Never remove the fuel filler cap while the engine is running. Select bare ground for fueling and move at least 10 feet (3 m) from the fueling spot before starting the engine. Wipe off any spilled fuel before starting your machine. Warning! Check for fuel leakage while refueling and dur ing operation. If fuel leakage is found, do not start or run the engine until the leak is fixed and any spilled fuel has been wiped away. Take care not to get fuel on your clothing. If this happens, change your clothing immediately. Different models may be equipped with different fuel caps. HT 100, HT 101, HT 130, HT 131 English Toolless cap with grip Warning! In order to reduce the risk of fuel spillage and fire from an improperly tightened fuel cap, correctly position and tighten the fuel cap in the fuel tank opening. 001BA220 KN To do this with this STIHL cap, raise the grip on the top of the cap until it is upright at a 90° angle. Insert the cap in the fuel tank opening with the raised positioning marks on the grip of the cap and on the fuel tank opening lining up. Using the grip, press the cap down firmly while turning it clockwise as far as it will go (approx. 1/4 turn). Fold the grip flush with the top of the cap. Grip the cap and check for tightness. If the grip does not lie completely flush with the cap and the detent on the grip does Misaligned, damaged or broken cap N If the cap does not drop fully into the opening when the positioning marks line up and/or if the cap does not tighten properly when twisted, the base of the cap may be prematurely rotated (in relation to the top) to the closed position. Such misalignment can result from handling, cleaning or an improper attempt at tightening. 001BA226 KN 001BA227 KN Always check your power tool for proper Left: Base of cap in closed position (with open space) Right: Base of cap correctly positioned for installation the base of the cap into the correct position. Then, twist the cap clockwise, closing it normally. N If your cap still does not tighten properly, it may be damaged or broken; immediately stop use of the unit and take it to your authorized STIHL dealer for repair. Screw Cap Warning! Unit vibrations can cause an improperly tightened Take off the chain guard (scabbard) and inspect the pole pruner for proper condition and operation. (See the maintenance chart near the end of the spillage and fire, tighten the fuel filler information. Before Starting instruction manual.) cap by hand as securely as possible. Instruction Manual for additional See also the "Fueling" chapter in your Warning! fuel filler cap to loosen or come off and spill quantities of fuel. In order to reduce the risk of fuel not fit in the correspond- N To return the cap to the open condition and operation before starting, ing recess in the filler position for installation, turn the cap particularly the throttle trigger, throttle opening, or if the cap is (with the grip up) until it drops fully trigger lockout, stop switch and cutting loose in the filler opening, into the tank opening. Next, twist the attachment. The throttle trigger must the cap is not properly cap counterclockwise as far as it will move freely and always spring back to seated and tightened and go (approx. 1/4 turn) – this will twist the idle position. Never attempt to mod- you must repeat the ify the controls or safety devices. above steps. HT 100, HT 101, HT 130, HT 131 English Warning! Never operate your power tool if it is damaged, improperly adjusted or maintained, or not ...
Other models in this manual:Garden Tools - STIHL HT 100 (2.33 mb)
Garden Tools - STIHL HT 101 (2.33 mb)
Garden Tools - STIHL HT 130 (2.33 mb)
Garden Tools - STIHL HT 131 (2.33 mb)