Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  
downloaded: 0   File size: 790 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

Chicago. IL 60684 FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS DRILL If this Craftsman Cordless Drill falls to give complete satisfaction within one year from the date of put.chase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears wilt replaceit, freeof charge. If this cordless drill isused for commercial or rentatpurposesthiswarranty applies for only 90 days from the dateof purchase. This warranty gives you specific lega! rights, andyoumayalsohaveotherrights whichvary

downloaded: 2   File size: 413 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

113.213832 DRILL PRESS WITH 1 4 HP MOTOR N j'M'* • V ,')p ^ " j-tif -'■a, ft“ *' 3' '*'*> 'o.V * tt'i- shf)vl 1 ■ pin"’' fWjl* 'Tl'Xl® dr'd S^'id 'i'Jrr'b(>' n a s*fp p acp'o* 'utu'** ubP CAUTION: R«»d OF.NER* and ADDITION/ ' SAFETY INSTRUCTIONS carefully CRRFTSMRN MOTORIZED 10 INCH BENCH MODEL DRILL PRESS • assembly • operating • repair parts FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS H within on« year Oom tha dal« of pure Mm Ihi* Craftaman Or Ml Ptaa* fails dua to a d*ta

downloaded: 2   File size: 698 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

• Do not use a wrench to tighten or loosenthe chuck ja.w8. _k WARNING: Make sure to insertthe drillbit straight into the chuckjaws. Do not insertthe drillbit into the chuckjaws at an angle then tighten, as shownin figure1O.Thls could cause the drill bit to be thrown from the drill,resultingin possib]e seriouspersonal injuryor damageto the chuck. WRONG Fig.10 REMOVING BITS See F_jure g. • Lock the sw(tch t_gar by placing the directionof rotation selector in the center position. • Loosenthe chuckj

downloaded: 1   File size: 2 mb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

SCREWDRIVER BIT BiTSTORAGEAREA Fig. 8 13 INSTALLINGBITS See Figures 9 -10. [] Lock the switch trigger by placing the direction of rotation selector in the center position. [] Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws. [] Insert the drill bit. _ WARNING: Make sure to insert the drill bit straight into the chuck jaws. Do not insert t

downloaded: 1   File size: 3 mb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

o o @ustemer He_p L_n. t °8@@°843°1682 Safety _nstructions KnstatJation Operation Maintenance Parts List Espa_oi Sears, Roebuck and Co=, Hoffman Estates, mL60179 USA Part No. 1372!910001 GENERAL SAFETY INSTRUCTIONS !4. REMOVE ADJUSTING KEYS AND WRENCHES. SECTION PAGE From the habit of checking to see that keys and BEFORE USING THE DRILL PRESS adjusting wrenches are removed from the t0ol before Warranty ................... " ..... 2 turning "ON". Product Specifications ........... ...............

downloaded: 0   File size: 388 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. 7 . SYMBOLS Symbol Name Designation/ Explanation V Volts Voltage A Amperes Current Hz Hertz Frequency ( cycles per second) min Minutes Time Alternating Current Type or a characteristic of current Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load

downloaded: 2   File size: 698 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA V'_it the Craftsman web page: 983000-709 Save this manual for future reference 5-05 • Warranty .......................................................................................................................................................................... 2 • Introduction ......................................................................................................... ....

downloaded: 0   File size: 487 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

• Plug your hammer drill into power supply source. • Hold your drill firmly and place bit at point to be drilled. • Depress the switch trigger to start your drill. Do not lock the switch ON for jobs where your drill may need to be stopped suddenly. • Move the drill bit into the workpiece applying only enough pressure to keep the bit cutting. Do not force your drill or apply side pressure to elongate a hole. Let your drill and bit do the work. See Figure 11. ,_ WARNING: Be prepared for binding or

downloaded: 0   File size: 518 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

315.110780 Save this manual for future reference _l, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Sears, Roebuck and Coo, Hoffman Estates, IL 60179 USA NRTL 972000-517 4-98 • Warranty .......................................................................................... _.............................................................. 2 • Introduction and Product Specifications ...........................................................

downloaded: 0   File size: 790 kb   Manafacture: Craftsman  
Category: Power Screwdrivers and Drills
@name

Therefore, you should charge tt at least 5 hours prior to use NOTE:Your drill wltl not reach fult charge the first ttme it is charged. Allow several cycles (drilling followed by recharging) for your drill to become fully charged, DRILL SELECTOR SWITCH TRIGGER WRIST STRAP TO CHARGE 1, Connect charger to your drill by inserting charger plug Into input jack, NOTE: As shown In Figure 1, input Jack is located at the rear of toot 2 Charger can be used with normal house voltage of 110.120 volts, 60 Hz.





Category