17, located in the machine base. Fig. 17 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING DRILL PRESS The switch (A) Fig. 18, is located on the front of the drillpress head. To turn the drill press “ON” move the switch up to the “ON” position. To turn the drill press “OFF” move the switch down to the “OFF” position. 10 R Q Fig. 15 S T Fig. 16 A A Fig. 18 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switchshould be locked in the “OFF” position to pre

For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). FRANCAIS : PAGE 34 10" Bench Drill Pre s s (Model SM300) PART NO. 638517-00 10-30-05 Copyright © 2005 Delta Machinery ESPANOL: PAGINA 18 To learn more about DELTA MACHINERYvisit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). FRANCAIS : PAGE 34 GENERAL SAFETY RULES Woodworking can be dangerous if safe and prope

12 Y X Fig. 13 Z ASSEMBLING HEADSTOCK TO COLUMN AND BASE To assemble the headstock to the column: 1. Place the drill press head (P) Fig. 9 on the column as far as it will go. NOTE: Be sure the head-locking screws (R) are do not block the drill press head from fully seating on the column. To reduce the risk of injury, always use at least two people when lifting. 2. Align the head (P) Fig. 10 with the table (Q) and the base (B). 3. Tighten the two head-locking screws (R) Fig. 9 with the 5 mm hex w

230229 230229764321 Figure 6.8 Alternate cylinder assignment 2 alternate cylinders are provided for each head in zone 12 (inner side). When an access request to physical sector 5 is specified, the device accesses the alternated sector in the alternate cylinder instead of sector 5. When an access request to sectors next to sector 5 is specified, the device seeks to cylinder 0, head 0, and continues the processing. (3) Automatic alternate assignment The device performs the automatic alternate assi

2) The device shall pause an Ultra DMA burst by negating DDMARDY-. 3) The host shall stop generating HSTROBE edges within tRFS of the device negating DDMARDY-. 4) If the device negates DDMARDY- within tSR after the host has generated an HSTROBE edge, then the device shall be prepared to receive zero or one additional data words. If the device negates DDMARDY- greater than tSR after the host has generated an HSTROBE edge, then the device shall be prepared to receive zero, one or two additional da

5-68 C141-E050-02EN 5.3 Host Commands Table 5.13 Command code and parameters (2 of 2) Command name Error register (X’1F1’) Status register (X’1F7’) BBK UNC INDF ABRT TK0NF DRDY DWF ERR WRITE VERIFY V V V V V V V READ VERIFY SECTOR(S) V V V V V V V RECALIBRATE V V V V V SEEK V V V V V INITIALIZE DEVICE PARAMETERS V V V V IDENTIFY DEVICE V V V V IDENTIFY DEVICE DMA V V V V SET FEATURES V V V V SET MULTIPLE MODE V V V V EXECUTE DEVICE DIAGNOSTIC * * * * * V READ LONG V V V V V V WRITE LONG V V V V

(6) Read/write circuit The read/write circuit uses a LSI chip for the read/write preamplifier. It improves data reliability by preventing errors caused by external noise. (7) Controller circuit The controller circuit consists of an LSI chip to improve reliability. The high- speed microprocessor unit (MPU) achieves a high-performance AT controller. 2.2 System Configuration 2.2.1 ATA interface Figures 2.3 and 2.4 show the ATA interface system configuration. The drive has a 44-pin PC AT interface c

USE A GOOD GRADE OF PLYWOOD WITH A MINIMUM 3/4" THICKNESS. DO NOT MAKE THE MOUNTING BOARD FROM PARTICLE BOARD SINCE PARTICLE BOARD BREAKS EASILY. 2. Use a plywood board base, with the minimum dimensions as shown in Fig. 4 for mounting the drill press base to a supporting surface. 3. Place the drill press base (D) Fig. 5, centered on the supporting surface (E). MAKE SURE THERE IS AT LEAST 3" ON ALL FOUR SIDES OF THE BASE AS SHOWN IN FIG. 5. 4. Drill two 3/8" diameter holes through the holes (A) F

1. Insert bit into chuck. 2. Lower the chuck (C) Fig. 25, to the depth you wish the holes to be drilled. Then lock the quill in position by tightening quill locking lever (E). NOTE: Quill locking lever (E) is spring-loaded and can be repositioned by pulling out on the handle and repositioning the hub of the handle on the bolt located underneath the hub. 3. Depress spring-loaded button (F) Fig. 25, and rapidly move stop nut (A) until bottom of nut (A) contacts stop (G). Then hold the pinion shaft

When making repairs, be sure to lock the start switch in the “OFF” position. An accidental start-up can cause injury. 22. MAKE YOUR WORKSHOP CHILDPROOF WITH PADLOCKS, MASTER SWITCHES, OR BY REMOVING STARTER KEYS. The accidental start-up of a machine by a child or visitor could cause injury. 23. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE. DO NOT USE THE MACHINE WHEN YOU ARE TIRED OR UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR MEDICATION. A moment of inattention while operating power