Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Check with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is properly grounded. Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system. DO NOT close vent tube or connect other type faucet or valves to the tank. Use only the InSinkErator faucet supplied. Use only parts provided. Contact an authorized InSinkErator Service agent for repairs or replacement components. Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Property Damage: To avoid water damage, replace any loose or split tubing. Periodically inspect the unit for any signs of leakage and immediately remove from service any unit suspected of leaking. A hot water faucet, like any water heater, has a limited life and will eventually fail. To avoid possible property damage, this hot water faucet should be regularly examined for leakage and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage. WARRANTY INFORMATION 1-year warranty Covers all replacement parts and labor to correct defects in material or workmanship in the faucet system, excluding the replaceable filter cartridge, for the full warranty period from the date of installation in your home. If warranty service is required during the warranty period, contact an authorized InSinkErator service agent to replace or repair the unit in your home at no cost to you. If your faucet is replaced rather than repaired, the warranty on the new unit shall be for the duration of the remaining portion of the original dispenser’s warranty. Note: Warranty is determined by unit serial number and/or date of installation. Purchase or installation receipt may be required to verify warranty status. When service is required, and for the location of your nearest factory authorized service center, call toll free 1-800-558-5700. The foregoing warranty does not apply to damage or inoperation resulting from accident, alteration, misuse, abuse, improper installation, installation not in accordance with these instructions or local electrical and/or plumbing codes. We do not assume any responsibility for consequential damage. Install using genuine InSinkErator® manufactured components only. Use of non InSinkErator components will void your warranty. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. CARE AND USE Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing unit. Use only a properly grounded and polarized electric outlet. ADJUSTING THE THERMOSTAT SEASONAL STORAGE/DRAINAGE Tank temperature is factory preset approx. 200° to 200°F, which mixes with cool tap water to produce an output water temperature of approx. 110°F. To reset the tank thermostat to 200°, turn the indicator one notch to the right of vertical. After adjusting, lift faucet handle for 20 seconds for water to re-heat to the new setting. To adjust water temperature, turn thermostat dial on the front of the tank clockwise to increase temperature or turn counter clockwise to decrease temperature. Repeat if necessary. All changes should be minimal. Scalding Hazard: Do not allow water to boil. May result in severe burns. PROPERTY DAMAGE Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service. To avoid water damage from leakage, replace all cut, loose or split tubing. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage. Anytime the hot water faucet is not used for extended periods of time, unplug and drain unit. If it is below freezing you will need to unplug the unit and drain it. Disconnect power from unit. Turn faucet lever to warm and allow water to flow until it is cool. Shut the faucet off at the valve. Remove drain screw located on bottom center of water tank and drain the water into empty pail. Empty the tank and then reinstall drain screw onto the bottom of tank, turning until snug. Do NOT over tighten. To place back in working order, fill tank with water and re-connect the plug. CLEANING THE FAUCET AND TANK Only use mild cleaners to clean the faucet and plastic components. Cleaners with acids, abrasives, alkaline or organic solvents will result in deterioration of the plastic components and void the warranty. Please read Troubleshooting Guide and/or visit www.insink...
Other models in this manual:Water Dispensers - UWL (1.3 mb)