• Sanding should be done in a manner to reduce tracking of paint dust outside the work area. Cleaning and Disposal • All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. • Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedu

. Children should be supervised to ensure that they do not play with the appliance. 7 Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. Warning! The vibration emission value during actual use of the power to

. Do not attempt to cut a branch when the diameter of the branch exceeds the cutting length of the tool. . Always remove the battery from the tool and place the chain cover assembly over the chain when storing or transporting the tool. . Keep the saw chain sharp and properly tensioned. Check the tension at regular intervals. . Switch the tool off, allow the chain to stop and remove the battery from the tool before carrying out any adjustment, servicing or maintenance. . Only use genuine replacem

After approximately 1 hour of charging, the red charging indicator will go off and the green ‘end of charge’ indicator will come on. The battery is now fully charged. . Remove the battery (10) from the charger (23). Installing and removing the saw chain (fig. D - F & H) Always wear protective gloves when installing or removing the saw chain (8). The saw chain (8) is sharp and can cut you when it is not running. . Place the tool on a firm and stable surface. . Loosen the 2 Allen screws (14) using

+40.C +10.C Charge only at ambient temperatures between 10°C and 40°C. The charger is intended for indoor use only. Your charger is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. Electrical safety Your charger is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the

. Follow the manufacturer's sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback. Safety recommendations for the chainsaw . We strongly recommend that first time users obtain practical instruction in the use of the chainsaw and protective equipment from an experienced user. Initial practice should be completed sawing logs on a saw horse or cradle. . We recommend that when carrying the chainsaw that you make sure that the brak

• DO NOT OVER-TENSION CHAIN. Refer to "ADJUSTING CHAIN TENSION" for proper method of tensioning chain. 18 Volt Cordless Chain Saw INSTRUCTION MANUAL • Retighten chain frequently during first two hours of use. Catalog Number CCS818 Thank you for choosing Black & Decker! to register your new product. PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON: If you have a question or experience a problem with your Black & Decker purchase, go to HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS for insta

Retighten the two retention bolts (11) securely. Check that the correct tension has been set by lightly pulling on the chain. The tension is correct when the chain snaps back after being pulled 1/8” inch (3 mm) away from the guide bar. There should be no "sag" between the guide bar and chain on the underside. Note: Do not over tension the chain as this will lead to excessive wear and reduce the life of the bar and chain. It will also lead to reduced product performance. Note: With first use and

Refer to “CHAIN TENSION ADJUSTMENT" for proper method of tensioning chain. • Retighten chain frequently during first two hours of use as chain breaks in. TTHANKHANK YOUYOU FORFOR CHOOSINGCHOOSING BBLACKLACK & D& DECKERECKER! G! GOO TTOO WWWWWW.B.BLACKANDLACKANDDDECKERECKER.. COMCOM/N/NEWEWOOWNERWNER TTOO REGISTERREGISTER YOURYOUR NEWNEW PRODUCTPRODUCT.. BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL 1-800-544-6986 BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,

These include: . Injuries caused by touching any rotating/moving parts. . Injuries caused when changing any parts, blades or accessories. . Injuries caused by prolonged use of a tool. When using any tool for prolonged periods make sure you take regular breaks. . Impairment of hearing. . Health hazards caused by breathing dust developed when using your tool (example:- working with wood, especially oak, beech and MDF). 10 Use Switching on and off (fig. H) For your safety, this tool is equipped wit