Ignited Vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area. NOTE: Dispose of the old fuel/oil mix in accordance to Federal, State and Local regulations. Remove fuel capWARNING: slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place. Add fuel in a clean, WARNING: well ventilated outdoor area. Wipe up any spilled fuel

A 3-wire extension cord (an extension cord with a ground) that uses a NEMA type connector (parallel blade, U ground) is recommended. Extension cords are available from your local retailer. Use only round- jacketed extension cords approved for outdoor use. • This tool is double-insulated. Repair or replace damaged cords. • To reduce the risk of electrical shock, this unit has a polarized plug (one blade is wider than the other). This unit will fit with a polarized plug in one way only. If the plu

8-211505 HOUSING (R) 1 44 MC-6154-211504 CONNECTOR 1 10 MC-9040-310175 BAR 1 45 MC-6017-211503 FRONT-HAND GUARD 12 MC-6228-211506 OIL PIPE ASS'Y 1 46 MC-6228-211303 FIXED ACC'Y 1 13 MC-6076-210503 WASHER 1 48 MC-6SDABB04-16 SCREW 14 MC-6056-211502 SWITCH BUTTON 1 49 MC-6079-211503 SPRING 1 15 MC-6066-211501 OIL TENK 1 50 MC-6038-211506 HOUSING (L) 16 MC-6028-211502 TRIGGER 1 51 MC-6086-211501 REAL COVER 1 17 MC-6022-211502 SWITCH 1 52 MC-6228-211301 MOTOR GEAR BOX ASS'Y

SPIKES event saw chain breaks or derails during operation. 15. REAR HAND GUARD The chain catcher is designed to intercept a whipping chain. 16. SPROCKET 17. OIL TANK WINDOW 18. CORD RETAINER 19. CHAIN CATCHER 20. CARRY CASE (Available on some models) A B B C A B B C RULES FOR SAFE OPERATION KICKBACK SPECIFICS Kickback can lead WARNING: to dangerous loss of control of the chain saw and result in serious or fatal injury to the saw operator or to anyone standing close by. Always be alert. Rotationa

To reduce this risk, always engage the chain brake before starting. Never attempt to start the chain saw when the guide bar is in a cut or kerf. English As soon as the engine is running, immediately blip the throttle trigger, which will disengage the starting throttle lock and allow the engine to settle down to idle. Warning! When you pull the starter grip, do not wrap the starter rope around your hand. Do not let the grip snap back, but guide the starter rope to rewind it properly. Failure to f

NRemove the shroud (2). Preheating the carburetor At temperatures below +50°F (+10°C): 1 0001BA002 KN NPull the shutter (1) out of the summer position (s). 0001BA003 KN NFit the shutter in the winter position (r) – symbol rfacing up. N Fit the shroud. Heated air is now drawn in from around the cylinder to warm the carburetor – this helps prevent carburetor icing. At temperatures above +70°F (+20°C): N Always return the shutter to the summer position (s) to avoid engine running problems and overh

N Select sharpening tools according marked on the file holder. Rest the file holder on the top plate and depth to chain pitch. gauge. 689BA025 KN As these requirements can be met only N Clamp the bar in a vise if necessary. N Lock the chain – push hand guard forward. N To rotate the chain – pull hand guard against handle to disengage the chain brake On models with Quickstop Plus, also press down the throttle trigger lockout lever. N Always file from the inside to the outside of the cutter. N The

: Use a hook to pull the fuel pickup body out of the tank and take it off the hose. : Push the new pickup body into the hose. : Place the pickup body in the tank. 001BA161 KN 001BA160 KN 001BA163 KN 001BA162 KN 165BA003 KN English / USA Chain Lubricant For automatic and reliable lubrication of the chain and guide bar – use only an environmentally compatible quality chain and bar lubricant with non-fling additive or the rapidly biodegradable STIHL BioPlus is recommended. Biological chain oil must

Unscrew the slotted nuts (4) . 138BA002K 4 MS 360 C 43 english / USA 6 5 138BA003K : Remove the foam filter element (5) from the front half (6) and clean or replace as necessary. : Knock the two halves of filter out on the palm of your hand or blow them clear with compressed air from the inside outwards. In case of stubborn dirt: : Wash the filter components in STIHL universal cleaner or a clean, non-flammable solution (e.g. warm soapy water) and then dry. Do not use a brush to clean the fleece