Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 0   File size: 2 mb   Manafacture: Husqvarna  
Category: Chainsaws

This line should be perfectly horizontal and at right angles (90°) to the chosen felling direction. Felling cut The felling cut is made from the opposite side of the tree and it must be perfectly horizontal. Stand on the left side of the tree and cut on the pull stroke. Make the felling cut about 3-5 cm (1.5-2 inches) above the bottom directional cut. Set the spike bumper (if one is fitted) just behind the felling hinge. Use full throttle and advance the chain/bar slowly into the tree. Make sure

downloaded: 2   File size: 2 mb   Manafacture: Husqvarna  
Category: Chainsaws
@name

See instructions under surface. the heading What is what? to find out where it is on your model. Lubricating cutting equipment ! WARNING! Poor lubrication of cutting equipment may cause the chain to snap, which could lead to serious, even fatal injuries. Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather. As a chain saw manufacturer we have developed an optimal chain oil which,

downloaded: 4   File size: 1 mb   Manafacture: Husqvarna  
Category: Chainsaws
@name@name

Hold chain saw firmly with both hands when using. For your own safety, please read and follow the safety precautions in this manual before attempting to operate your chain saw. Improper use can cause serious injury. This product has been tested at a computed kickback angle (CKA) and conforms to ANSI B175.1-2000, Annex C. CAN/CSA-Z62.1-03 2-Cycle Gas Chainsaws Model TB5018CC Model TB5020CC INTRODUCTION INTRODUCTION THANK YOU Thank you for buying this quality product. This modern outdoor power too

downloaded: 1   File size: 28 mb   Manafacture: Husqvarna  
Category: Chainsaws
@name@name@name

Maintenance Procedures Most guide bar problems can be prevented merely by keeping the chain saw well maintained. Incorrect filing and non-uniform cutter and depth gauge settings cause most guide bar problems, primarily resulting in uneven bar wear. As the bar wears unevenly, the rails widen, which may cause chain clatter and difficulty in making straight cuts. Insufficient guide bar lubrication and operating the saw with chain that is too tight will contribute to rapid bar wear. To help minimize

downloaded: 13   File size: 265 kb   Manafacture: Husqvarna  
Category: Chainsaws
@name

02 PLATE 1 32 MC-6SDABB03-18 SCREW 1 66 MC-6SLABB03-06 SCREW 33 MC-6228-210105 OIL PUMP ASS'Y 1 67 MC-6010-211301 WIRE 1 34 MC-6188-211501 PULL BAR 1 68 MC-6SDABB04-14 SCREW 3 35 MC-6114-211501 PULL PLATE 1 Stocking Codes are: A - Dealer stocked B - Distributor stocked C - Factory stocked

downloaded: 1   File size: 2 mb   Manafacture: Husqvarna  
Category: Chainsaws
@name@name@name

If you feel comfortable sharpening your own saw chain, special tools are available from your Authorized Service Center. Never remove, WARNING: modify or make inoperative any safety device furnished with your unit. The Chain Brake® / Hand Guard and low-kickback saw chain are major safety features provided for your protection. CHAIN REPLACEMENT INFORMATION There may be other quality equivalent replacement components for achieving kickback protection. Bar Length Drive Links Part Number 16” Bar 55 D

downloaded: 0   File size: 6 mb   Manafacture: Husqvarna  
Category: Chainsaws
@name

Asegurese de aflojar el tornillo de la barra guia lo suficiente para dejarlo apretado con la mano; gire hacia la derecha el tensador de la cadena para tensar esta. Consulte el apartado Reemplazo de la barra y de la cadena mas arriba en este manual, donde encontrara informacion adicional. . La cadena, estando fria, esta bien tensada cuando no hay holgura de la misma en la parte inferior de la barra guia, la cadena se siente bien ajustada en la barra, y puede avanzarse con la mano sin ningun atora

downloaded: 4   File size: 4 mb   Manafacture: Husqvarna  
Category: Chainsaws
@name

18.3 Install front handle. A Roll front handle into place. B Install front handle screws (4). C Use blue Loctite® . D Torque to 69 in-lbs. (8 Nm). © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 19. FUEL TANK TITLE 19. FUEL TANK 613GC SERVICE MANUAL 19 This section covers the disassembly, inspection, and assembly of the vibration isolaters, fuel tank, and rear handle. 19.1 Remove vibration isolator screws and wave washers on clutch side of saw. 19.2 Remove vibration isolator screws and wave washe

downloaded: 2   File size: 347 kb   Manafacture: Husqvarna  
Category: Chainsaws

3. Visually inspect the Hedgetrimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement. To store your Hedgetrimmer • The Hedgetrimmer blade cover/storage holder is provided with 2 hanging slots for storing the Hedgetrimmer on the wall.(See Pic L) • Ensure the blade cover/storage holder is fitted before storage. 1. The use of 2 number 10 screws (40mm in length) and the appropriate wall fixing plugs is recommended 2. Drill 2 holes 47mm horizontally a

downloaded: 11   File size: 347 kb   Manafacture: Husqvarna  
Category: Chainsaws

ageing. 6. Remove plug from mains before passing 3. Do not use the Hedgetrimmer if the electric Hedgetrimmer to another person. cables are damaged or worn. 7. Avoid operating while people especially chil4. Immediately disconnect from the mains elec-dren are nearby. tricity supply if the cable is cut, or the insula-8. Whilst using the Hedgetrimmer always be tion is damaged. Do not touch the electric sure of a safe and secure operating position. cable until the electrical supply has been dis-9. Ke





Category