You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to your local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructio

Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Razor knife or similar 4. 1/4" hex socket bit 5. Awl or similar tool 6. 5/16" hex socket bit 7. Audiovox Series 640/650 Video Module * FOR USE IN VEHICLES EQUIPPED WITH FACTORY INSTALLED REAR AIR CONDITIONING and WITH FACTORY OVERHEAD CONSOLE ONLY. May 19, 1999 Printed in the U.S.A INSTALLATION INSTRUCTION # 44-0024B MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY

dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. FIGURE 7 7. Secure bracket to sheetmetal frame using four (4) # 8 x 3/4" HWH TEKS screws ( item 1 pg 2 ). Secure O.E.M. ground wire (if applicable) using one of the screws. See Figure 8. FIGURE 8 6 8. If vehicle is equipped with an electronic compass, un

PREPARATION OF VEHICLE INTERIOR FIGURE 1 3. Install console mounting bracket (item 2 pg 2) over O.E. bracket on roof brace. Secure rear of bracket using (2) two O.E. screws. Secure front of bracket using (2) two #8 x 3/4" screws (item 1 pg 2) See Figure 2. INSTALLATION INSTRUCTION # 44-0026B 3 1. Carefully trim headliner as shown. Caution: Before cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. Make sure that the 8 1/2" cut is centered

Special tools and equipment, as well as specialized handling and care of product during installation, may be required. Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or similar tool 4. Razor k

d). Select ‘LAST MEMORY’ by using the DOWN button. General Video Password Preferen Exit Angle Mark Off On Off Set Last Memory Last Memory Screen Display *ON: The unit will return to the last position on the disc. *OFF: The unit will not return to the last position on the disc. 11 2) Select ‘VIDEO’ by using the LEFT/RIGHT buttons, press ‘ENTER’ to enter the VIDEO SETUP PAGE. General Video Password Preferen Exit Brightness Contrast 00 00 .. . . Video Setup Page Go To Video Setup Page Video Quality

SETTING THE PRESETS (FOR AM AND FM OR TV MODES) 1) Turn to the desired channel/broadcast frequency. 2) Press the SET button ; the display flashes. 3) Select desired Preset (1~6 button). SETTING THE SPEAKER MODE 1) With power off, Press the SET button five times to enter the speaker configuration mode. “I SP(or E SP)” appears on the VFD. 2) Press the 1 preset button to toggle between the “I SP” and “E SP” 3) When the desired mode is reached, press the ON/OFF button. - 17 Using the Remote Control

Turn on your Vehicle Entertainment System (VES) and select the source input to which the FLO TVservice is connected. (Note: Watching the FLO TVservice for an extended period of time with the engine OFF will run down the vehicle's battery.) 2. The VES screen will show the FLO TV splash screen and then the FLO TV preview channel. 3. If you are not subscribed, subscribe to the FLO TVservice by calling 888-99-FLOTV or by going online to The Device ID and Authorization Code of the FLO TV module ar

• Repeat All- repeats the disc that is playing. • Off As you toggle through the options, the repeat option changes. The selected repeat option loops repeatedly until it is turned off. K. PLAYING MP3 DISCS MP3 is a digital audio format. An audio CD-quality song is compressed into the MP3 format with no significant loss of audio quality. CD-R / RW discs that have been encoded in MP3 format are compatible with this device. Insert a MP3 Disc, the DVD player will initialize the disc and the directory