Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 0   File size: 3 mb   Manafacture: Genie  
Category: Safety Gate
@name

2" Carriage Bolt /4"-20 Hex Fmange Nut RAIL SECTION CONNECTION WOODEN DOORS DOOR ARMS SlideCollarover long Nook TO (SHORT AS POSSIBLE) >, c c_ E Mate Hooks LJo _J GJ _c F= < ARMS L0 SHde Collar over Joint J c _6 (LONG AS POSSIBLE] I Snap CHp behind Collar L_ _O O O @ CONNECT RAK TO POWER HEAD ATTACH RAK STRAP TO [ND RAK SECTION CONECTEEL_ARANDALACAJADELMOTOR [NSTALEELENSA_BLEDELCORRED_ZO MA_N_TICOA LASBARANDAS Attach Rail Strap to End Rail Section, A o Threaded stud of Rail strap should pass in

downloaded: 1   File size: 3 kb   Manafacture: Genie  
Category: Safety Gate

downloaded: 0   File size: 990 kb   Manafacture: Genie  
Category: Safety Gate
@name

An extension kit for an 8 foot high door is available. For Answers and Assistance: 1.800.354.3643 or visit SAVE THIS MANUAL FOR FUTURE REFERENCE PRE-INSTALLATION CHECK LIST FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM PRE-INSTALLATION CHECK LIST FOR HELP-1.800.354.3643 OR GENIECOMPANY.COM 2 Things to consider if you are planning to “do-it-yourself.” In many cases you will be replacing an existing door operator with a new one, however, if this will be the first operator installed there are some pr

downloaded: 0   File size: 2 mb   Manafacture: Genie  
Category: Safety Gate
@name

NOTE • Little effort is required to turn the Force Adjusting Knobs. • If the door stops moving while opening or closing, adjust the Open Force or Close Force Controls slightly clockwise (to slightly increase the force) and retry the step. • The Open Force and Close Force Controls are to be set to the minimum force necessary to ensure the door smoothly opens and closes completely. • Ensure the Carriage Assembly is engaged and is between the two Limit Switches before operating the Opener. Figure M

downloaded: 0   File size: 6 mb   Manafacture: Genie  
Category: Safety Gate
@name

8 2 Program IntelliCode® 2 Remote to Powerhead ............................9 Programming HomeLink®, Car2U®, IntelliCode® 1 remotes or wireless keypads ................................................................................................................10 Reference 3 Typical Installed Illustrations ................................................................ 11-13 Powerhead & Rail Assembled View ............................................................ 11 Typical Sectional Door

downloaded: 0   File size: 11 mb   Manafacture: Genie  
Category: Safety Gate
@name

6. Locate the wall console: • Within sight of the garage door, • At minimum height of 5 feet so small children are not able to reach it, and • Away from all moving parts of the door. 7. Install the Entrapment WARNING Label next to the wall console in a prominent location. 8. After installing the opener, the door must reverse within 2 seconds when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor. INFRARED PROTECTION FUNCTION 1. When garage door is opening, its moveme

downloaded: 2   File size: 11 mb   Manafacture: Genie  
Category: Safety Gate
@name

• Open garage door using wall console. – Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-2). • Close garage door using wall console. • When door contacts board, the door must stop (within 2 seconds) and reverse direction returning to open position. 2. Adjustment. • If the door: – Stops before it contacts the 2 x 4 board, it may simply be responding to an improperly set down limit. Return to pages 6-7 and repeat steps 1 through 10 to correct down limit. – Stops after

downloaded: 4   File size: 990 kb   Manafacture: Genie  
Category: Safety Gate
@name

1. Door springs and hardware. • Do not operate garage door automatically or TROUBLESHOOTING GUIDE Use This Guide To Correct Problems With Door Operator. manually if springs are broken. If These Solutions Do Not Work, – CONTACT A PROFESSIONAL FOR SERVICE. Call Customer Service at 1.800.35.GENIE 2. Door balance. • Close the door. • Pull emergency release knob down to release door from carriage assembly. • Raise door manually approximately 3 feet. – Door should stay in that position or close very s

downloaded: 6   File size: 2 mb   Manafacture: Genie  
Category: Safety Gate
@name

B Install Lens into slots in Motor Cover. • Insert Bottom hinges into slots provided in metal front cover of Power Head. • Flip Lens up and fasten with molded latches on lens. Ins tallation of Lens and Bulb Figure 14 Install Lens and Light bulb Transmitter Compliance Statement WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH 1 READ AND FOLLOW ALL INSTRUCTIONS. 2 Never let children operate or play with the Door Controls. Keep the Remote Control away from children. 3 Always keep the moving doo

downloaded: 0   File size: 17 mb   Manafacture: Genie  
Category: Safety Gate
@name@name@name

If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8). CAUTION Use 5/16"-18 x 1/2" Bolts FIG. 1-5 Rail - Power head assembly. FIG. 1-6 Chain adjustment. Chain Pulley Bracket (at wall end of rail) Chain T-Rail at center of rail assembly 1/8" T-Rail Chain Tighten nut to move pulley this direction Use 1/2" socket on adjustment nut Set assembled power head and rail aside. Begin with Section 2 INSTALLATION. Assembly for BELT DR





Category