Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 1   File size: 7 mb   Manafacture: Craftsman  
Category: Safety Gate
@name

Step 10, page 22 -Alternate floor mounting of the safety reversing sensor will require hardware that is not provided. Step 11, page 25 _ Generally, a one pie_ door does not require reinforcemenL tf your door is lightweight, you _e refer to the information relating to section_ doors on page 24. ,,Step 11, page 25 _Depending on your dooCs construction, you might need additional mounting hardware for the door brackeL oDo you have an a_ess door in addition to the garage dc_r? if not, Model 53702 Eme

downloaded: 1   File size: 174 kb   Manafacture: Craftsman  
Category: Safety Gate
@name

Instructions are given below for programming your opener to match the remote control's code. The additional remote control buttons can also activate other Security. garage door openers and/or light controls. (InstrucUons for programming light products are Included with those accessories.) SECURITY,4t, Garage Door Openers Program the Opener to Accept the Remote Control Code Select a remote control push button to operate the receiver° The large button is recommended for use with the garage door op

downloaded: 2   File size: 107 kb   Manafacture: Craftsman  
Category: Safety Gate
@name

CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. Connect the other end of the bell wire to the two opener terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the push button control. Use insulated staples (not supplied) to secure bell wire between receiver and ope

downloaded: 1   File size: 1 mb   Manafacture: Craftsman  
Category: Safety Gate
@name

2 Specifications .......................... 2 Accessories ............................... 2 Carton Check List ...................... 3 You'll Need Tools .................... 3 Safety Rules .............................. 4 Operation of Your Opener ............ 5 Maintenance Schedule ............... 5 Assembly 6 .................................. Installation Information ................. 9 Installation ........................... 9 Force& Limit Adjustment ............ 17 Safety Reverse Test .....

downloaded: 1   File size: 2 mb   Manafacture: Craftsman  
Category: Safety Gate
@name

CAUTION PLEASE READ THIS MANUAL CAREFULLY CONTENTS PAGE Safety Rules ................... 2 Operation of Your Opener ....... 3 Maintenance Schedule ......... 3 Features of Your Opener ........ 4 Specifications ................. 4 Accessories .................... 4 Carton Check List .............. 5 You'll Need Tools ............... 5 Assembly ...................... 6 Installation Information ......... 9 Installation ................... 10 Force & Limit Adjustment ........ 17 Safety Reverse Test .

downloaded: 0   File size: 7 mb   Manafacture: Craftsman  
Category: Safety Gate
@name

The light will turn ON and remain lit for approximately 4q/2 minutes when _wer is connected. Then the light will turn OFF. , If the bulb bums out prematurely due to vibration, replace it with a standard neck "Garage Door Ught Install the lens (except for Modef 53225) Apply slight pressure on IJsesides of the _ens and slide _e tabs into the slots in the end p_ef , Reverse the procedure to remove the fens° lnstalJation Step 8 Attach the Emergency Release Do not use the red handle to pull the door

downloaded: 0   File size: 4 mb   Manafacture: Craftsman  
Category: Safety Gate
@name@name

• ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might not reverse when required. Finished Ceiling Vertical Centerline Header Wall 2x4 Structural Supports Vertical Centerline Installation procedures vary according to garage door types. Follow the instructions which apply to your door. SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the

downloaded: 0   File size: 4 mb   Manafacture: Craftsman  
Category: Safety Gate
@name@name

If the opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6" (15 cm) above the floor), call for a trained door systems technician. Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLYINJUREDor KILLEDby a closing garage door. Safety Reversing Sensor 29 OPERATION IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death: 1. READAND FOLLOWALL WARNINGSAND INSTRUCTIONS. 2. A

downloaded: 2   File size: 2 mb   Manafacture: Craftsman  
Category: Safety Gate
@name

Then bend cover forward and insert front tab in slot provided on mounting plate. Tab Slot P_ate ................................. ,,, 1111 , [H ", , _llJ,,,m,,,, ,,1 II I 8 Assembly Hit I i, ,,i I III I ,I, I IIIlllll II I , H,,I STEP 5 Tighten the Chain and Cable , ,, , H,,"H I I="= HI ,I,,H,, , .................................. Loosen Lock Tighten CAUTION: Keep the turned. chain from twisting as nuts are PROCEDURE: Thread the outer nut toward shown. (Loosen inner nut first, if necessary.) tro

downloaded: 0   File size: 10 mb   Manafacture: Craftsman  
Category: Safety Gate
@name@name

Fasten the manual near the garage door after installation. Periodic checks of the opener are required to ensure safe operation. Leer y seguir todas las reglas de seguridad y las instrucciones de operacion antes de usar este producto por primera vez. Guardar este manual cerca de la puerta de la cochera. Se deben realizar revisiones periodicas del abridor de puertas para asegurar su operacion segura. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A TABLE OF CONTENTS Introduction 2-7 Safety





Category