Install the receiver (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control(s). A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see it clearly, and there are no obstructions to door travel• DISCONNECT POWER TO THE GARAGE DOOR OPENER REFOREPROCEED

CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. Connect the other end of the bell wire to the two opener terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the push button control. Use insulated staples (not supplied) to secure bell wire between receiver and ope

(Se incluyen con esos accesorios instrucciones para programar productos de iluminacion.) KG 1 3 9 7 5 KG 1 3 9 7 5 1 2 O LOCK LIGHT KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 Instrucciones Codigo del Remoto 1. Oprima y suelte el boton “Aprender” de la unidad del motor. La luz indicadora de este boton estara encendida por 30 segundos. 2. En los 30 segundos, oprima y mantenga oprimido el boton del control remoto manual. 3. Suelte el boton cuando las luces de la unidad del motor empiecen a parpadear. Ya apren

Programming instructions are described and illustrated below. The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) KG 1 3 9 7 5 KG 1 3 9 7 5 1 2 OR LOCK LIGHT KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 Remote Coding Instructions 1. Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, press and hold

If the opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6" (15 cm) above the floor), call for a trained door systems technician. Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLYINJUREDor KILLEDby a closing garage door. Safety Reversing Sensor 29 OPERATION IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of severe injury or death: 1. READAND FOLLOWALL WARNINGSAND INSTRUCTIONS. 2. A

2 Specifications ............................... 2 You'll Need Tools ............................ 2 Safety Rules .................................. 3 Carton Check List ............................ 4 Accessories .................................... 5 Identify Your Door Type .................. 5 Assembly ........................................... 6 Installation .......................................... 10 Adjustment ................................ 18 Operation of Your Opener ..................

Fasten the manual near the garage door after installation. Periodic checks of the opener are required to ensure safe operation. Leer y seguir todas las reglas de seguridad y las instrucciones de operacion antes de usar este producto por primera vez. Guardar este manual cerca de la puerta de la cochera. Se deben realizar revisiones periodicas del abridor de puertas para asegurar su operacion segura. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A TABLE OF CONTENTS Introduction 2-7 Safety

• ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door might not reverse when required. Finished Ceiling Vertical Centerline Header Wall 2x4 Structural Supports Vertical Centerline Installation procedures vary according to garage door types. Follow the instructions which apply to your door. SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the

30 Using the Wall.Mounted Door Control THE PREMIUM CONTROL CONSOLE Lighted Push Button Press the lighted push button to open I _ -_-_._ or close the door. Press again to reverse the door during the closing Light cycle or to stop the door while it's utton opening. Lock Button Light feature Press the Light button to turn the opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2 mi

WARNING Mechanical WARNING Electrical CAUTION When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully. When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if