FOR YOUR SAFETY, KEEP LADDER AND ANTENNA AWAY FROM POWER LINES. CONTACT MAY CAUSE ELECTROCUTION Antenna Grounding and Safety Warning 1. Outdoor antennas and lead-in conductors from antenna to a building, should not cross over open conductors of electric light of power circuits.They should be kept away from all circuits to avoid the possibility of accidental contact. 2. Each conductor of a lead-in from an outdoor antenna should be connected with an antenna discharge unit. Antenna discharge units

insert mast through U-bolt.Tighten nuts securely (fig.5) (Mast sold separately). 6. Connect 2 mast sections as shown in figure 6 (included in SDV9201K only) ENAiming the Antenna 7. Connect a good quality RG-6 coaxial cable to the transformer. Slide the weatherproof boot over the connection firmly until it seals (fig.7) (Cable sold separately) fig. 7 fig. 8 8. Attach cable standoff to mast as shown in figure 8 (included in SDV9201K only) Aiming the Antenna Before permanently mounting the antenna

English EN 19 Pictures Browse recorded files • : Return to the home menu. • : Zoom in or out of the picture. • / : Rotate the picture clockwise or anti- clockwise by 90 degrees. • / : Return to the list of files or folders (see 'Browse recorded files' on page 19). • / : Select the previous or next picture. • / : Pause or resume the slideshow. • : Display control icons on the second page. • [16:9]/[4:3]: Select an aspect ratio. • :Tap to display the brightness bar, and then tap on the bar to adju

• Unit control mode: tap screen on car audio to control the music. Search for a track During play from iPod/iPhone, you can search through the music/video files to select preferred file for listening/watching. During playing, tap . » Search list is displayed. 2 Tap to select folder/file. 3 Tap on the screen to select desired song. 4 Tap on the selected song to play. Charge the iPod/iPhone When the iPod/iPhone is connected to the car audio system, the iPod/iPhone begins to charge. Tip • For cer t

34 EN 12 Others Play external audio/video input You can connect an external audio/video player to this system. 1 Connect a composite AV cable to • the AV-IN socket on the front panel, and • the audio and video output sockets of the external player. 2 Tap > to access the full menu with all feature icons displayed. 3 Tap [AV-IN 1] to display the playback interface. 4 Operate on the external player to start play (see the user manual of the external device). Tip •• If you connect this system to an e

Caution • This unit is designed for negative ground (ear th) 12 V DC operation only. • Always install this unit in the car dashboard. Other locations can be dangerous as the rearof the unit heats up during use. • To avoid shor t-circuit: before you connect, ensure that the ignition is off. • Ensure that you connect the yellow and red power supply leads after all other leads are connected. • Ensure that all loose leads are insulated with electrical tape. • Ensure that the leads do not get caught

Keep the batter y out of reach of children at all times! Read and understand all instructions before you use the device. If damage is caused by failure to follow instructions, the warranty does not apply. • Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. • The device is designed for negative ground (ear th) 12 V DC operation only. • To reduce the risk of traffic accidents, do not watch video when

4 Tap to exit. Others Tap on the playback interface. » The setup interface is displayed. • :Tap to display the [Music zone] interface for selecting a listening zone. • :Tap to display the [Fader/ Balance] interface for adjusting the fader and balance. • :Tap to display the [SubWoofer] interface for setting the sub-woofer. Adjust the fader and balance Set the sub-woofer • [On]/[Off]: Tap to turn on or off the sub- woofer. • / :Tap to set the volume of sub- woofer (0 dB to 14 dB). • [80 Hz]/[120 H

• Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. English 10 3 Connect the antenna and amplifier as illustrated, if applicable. You can connect the car audio to the amplifier through RCA-TO-RCA cables (not supplied). Connector Connect to 1 ANTENNA Antenna 2 FRONT LINE OUT R (Socket) Front right speaker 3 FRONT LINE OUT L (Socket) Front left speaker 4 REAR LINE OUT R (Socket) Rear right speaker 5 REAR LINE OUT L (Socket) Rear left speaker 6 SUBWO

3 Select “Philips” in the pairing list. 4 Enter default password “0000”. » [Paired Ok!] displays on the panel if pairing is successful. » The paired device connect to the car audio system automatically. To disconnect the bluetooth 1 Press MENU. » [BT DIS-CONNECT] displays. 2 Press OK/MUTE. » [Dis Connect Ok!] displays if disconnection is successful. To re-connect the bluetooth 1 Press MENU. » [BT RE-CONNECT] displays. 2 Press OK/MUTE. » [Waiting] displays. » [Connect Ok!] displays if re- connect