Improper phasing causes a loss of bass response. • When used in the BRIDGED Mode, the speaker wires should be connected to the output terminals of the amplifier as shown. • When operating 4-speaker system, the impedance of the speaker is an important factor. Do not use less than a 4 ohm load in BRIDGED mode. • Do not use speakers in parallel at less than a 2 ohm load per channel in STEREO mode. • Too low of an impedance or load may cause permanent damage to your amplifier. It is best to chec

Your selection of our products for your sound system indicates that quality sound is important to you too. At SAS, we take great pride in manufacturing revolutionary audio product, and through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created the Bazooka Pro20 line of power amplifiers. We hope that you will take as much pride in owning and using one of these high quality audio products as we do in designing and manufacturing them. When properly

Your selection of our products for your sound system indicates that quality sound is also important to you too. At SAS, we take great pride in manufacturing revolutionary audio products, and through the years of engineering expertise, hand craftsmanship and critical testing procedures, we have created this high-performance series of amplifiers. We hope that you will take as much pride in owning and using one of these high-quality audio products as we do designing and manufacturing them. When pro

The gain controls should be adjusted very slowly. It may help to have another person to assist you by adjusting the gain controls while you listen for distortion. 15 TROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause var

Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat. Select the location in which you wish to mount the amplifier. Use caution when mounting amplifier, there are many wires, gas lines, vacuum lines, brake lines as well as a gas tank in the automobile. Make sure you know where they are when mounting the amplifier to avoid puncturing lines, shorting wi

factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. HIGH LEVEL CONNECTIONS (OPTIONAL) CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or radio. TWO CHANNEL CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) BASS POWER X-OVER BOOST RIGHT + RIGHT - LEFT - GREEN LEFT

600W 65W x 4 85W x 4 175W x 2 20Hz-22KHz >90dB .03% 200mV-6V 1.0V-10.0V 10.5VDC-15.0VDC HP/FULL/LP HP/FULL/LP 60Hz-400Hz 12dB/Oct 0-12dB @ 45Hz Yes Yes 7.5A 3 x 20A 1 15 12 /” x 10 /” x 2 /” 2 48 * Low-pass Only ** Marine version of the ELA1500 and ELA 460, additional features include: Stainless Steel screws, aluminum end plates, marine coated circuit board, gold plated connectors, salt, fog and UV tested. Due to continuing product improvement, specifications subject to change without notice. 16

You should be able to use about 3/4 volume before the system gets loud but not distorting. It is very important when making these adjustments that you do not over drive the speakers (at point of distortion) this will cause permanent damage to the speakers. If you are unable to achieve 3/4 volume before distortion you will need to adjust gain control (in this case you would reduce the gain). The gain controls should be adjusted very slowly. It may help to have another person to assist you by adju

Short Circuit Protectio. The circuit protects the amplifier from damage due to a short found in the speakers or wiring. If one of the speakers or its wiring comes in contact with ground, the amplifier will shut down. To resume normal operation, correct the problem and turn the head unit off, then back on. The amplifier will reset and play again. Thermal Protectio. To protect the amplifier circuitry against damage caused by prolonged exposure to high temperatures, a thermal protection circuit is

factory radio). This connection will allow you to connect directly to the speaker output of the radio with out the need of an external adapter. Determine the type of radio you have and make one of the following connections. HIGH LEVEL CONNECTIONS (OPTIONAL) CAUTION! Before making any connections determine the type of radio to avoid possible damage to amplifier and/or radio. TWO CHANNEL CONNECTIONS: FLOATING GROUND RADIO (MOST COMMON TYPE) RIGHT + RIGHT - LEFT - GREEN LEFT + GREEN/BLACK (NOT USED