Login:
Votes - 0, Average rating: 0 ( )

User manual Philips, model CEM2000/51

Manafacture: Philips
File size: 3.27 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


• Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. English 10 3 Connect the antenna and amplifier as illustrated, if applicable. You can connect the car audio to the amplifier through RCA-TO-RCA cables (not supplied). Connector Connect to 1 ANTENNA Antenna 2 FRONT LINE OUT R (Socket) Front right speaker 3 FRONT LINE OUT L (Socket) Front left speaker 4 REAR LINE OUT R (Socket) Rear right speaker 5 REAR LINE OUT L (Socket) Rear left speaker 6 SUBWOOFER Subwoofer Connection: for cars without ISO connectors Caution Be • sure to connect the black ground (earth) lead first. Note on the power supply lead (yellow) • When you connect other devices to this apparatus, ensure that the rating of the car circuit is higher than the total fuse value of all the connected devices. Notes on speaker connection • Never connect speaker wires to the metal body or chassis of the car. • Never connect speaker wires with stripes to one another. Connection: for cars with ISO connectors Caution • Ensure that all loose leads are insulated with electrical tape. 1 Pull out the ISO connectors from car dashboard and connect them to the bigger end of the supplied standard connector. 2 Connect the other end of the supplied standard connector to the unit. EN 11 1 Green/black strip Left speaker (Rear) 2 White/black strip Left speaker (Front) 3 Gray/black strip Right speaker (Front) 4 Purple/black strip Right speaker (Rear) e RED Ignition key +12V DC when ON/ACC f BLUE Motor/electric antenna relay control lead/Amplifier relay control lead g BLACK Ground h YELLOW To the +12V car battery which is energized at all times 4 Connect the supplied standard connector to the unit. Tip The pin arrangement • for the ISO connectors depends on the type of vehicle you drive. Be sure to make proper connections to prevent damage to the unit. 1 Connect the antenna and amplifier as illustrated, if applicable. Connector Connect to 1 ANTENNA Antenna 2 FRONT LINE OUT R (Socket) Front right speaker 3 FRONT LINE OUT L (Socket) Front left speaker 4 REAR LINE OUT R (Socket) Rear right speaker 5 REAR LINE OUT L (Socket) Rear left speaker 6 SUBWOOFER Subwoofer 2 Cut off the bigger end of the supplied standard connector. 3 Check the car’s wiring carefully and connect them to the supplied standard connector. b a c d a b a c d a b e f c d g h b c d English EN 12 4 Remove the mounting sleeve with the supplied disassembly tools. 5 Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve. Note If the unit • is not fixed by sleeve but by the supplied screws, skip this step. 5mm5mm5mm5mm Mount into the dashboard 1 If the car does not have an on-board drive or navigation computer, disconnect the negative terminal of the car battery. • If you disconnect the car battery in a car that has an on-board drive or navigation computer, the computer may lose its memory. • If the car battery is not disconnected, to avoid short-circuit, ensure that the bare wires do not touch each other. 2 Ensure that car dashboard opening is within these measurements: 3 Remove the two screws on the top of the unit. 183 mm 53.5mm 5mm EN 13 Attach the front panel 1 Attach the trim plate. 2 Insert the right side of the panel in the chassis until it is correctly engaged. 3 Press the left side of the panel until the mechanism locks it into place. Install remote control battery Caution Risk of explosion! K • eep batteries away from heat, sunshine or fire. Never discard batteries in fire. • Risk of decreased battery life! Never mix different brands or types of batteries. • Risk of product damage! When the remote control is not used for long periods, remove the batteries. • Perchlorate Material - special handling may apply. See perchlorate. For first-time use: 1 Remove the protective tab to activate the remote control battery. 6 Place the supplied rubber cushion over the end of the mounting bolt. 7 Slide the unit into the dashboard until you hear a click sound. 8 Reconnect the negative terminal of the car battery. 5mm English EN To replace the remote control battery: 1 Open the batter y compar tment. 2 Inser t one CR2025 batter y with correct polarity (+/-) as indicated. 3 Close the battery compar tment. Turn on 1 Press to turn on the unit. • To turn off the unit, press for over 3 seconds. Select country/region Note • Select correct country/region for this unit, other wise the unit can not work properly. 1 Press to turn on the unit. » [SELECT OPERATING REGION] is displayed. 2 Rotate to select an option: • [USA] (United States) • [Latin] (Latin America) • [Europe] ( Western Europe) • [ASIA] (Asia Pacific) • [Mid-East ] (Middle East) • [Russia] (Russia) 3 Press to confirm. Set clock 1 Press MENU. 2 Press or repeatedly until currently time is displayed. 3 Turn clockwise to set hour. 4 Press to confirm. 5 Turn anti-clockwise to set minute. 6 Press to confirm. View clock 1 Press and hold OPTIONS repeatedly until the ...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category