Login:
Votes - 3, Average rating: 3.7 ( )

User manual Brinkmann, model 810-8650-S

Manafacture: Brinkmann
File size: 13.08 mb
File name:
Language of manual:enes
Free link for this manual available at the bottom of the page



manual abstract


Step 8 Remove the left side shelf by unscrewing the four bolts. Step 9 Remove the side burner brass cap by using the small wrench to unscrew the two small screws. Step 10 Remove access panel on left side of grill for better view of gas orifice. Step 11 Use the gas orifice tool to remove LP brass orifice from the hole on the top of side burner. Step 12 Using gas orifice tool, install 1.35mm (RED) natural gas orifice. Be careful not to cross thread natural gas orifice. 1.35mm Existing Side Burner LP Gas Orifice Replacement Side Burner Natural Gas Orifice (identified by number) Side Burner 1.35mm (RED) Step 13 Replace the side burner brass cap to the burner. CAUTION: Some parts may contain sharp edges.Wear protective gloves if necessary. WARNING: Only use the specific orifice designated for your grill model. Always double check the millimeter size on the side of the orifice tip prior to installation. Use of any other orifice could lead to personal injury, property damage and void your grill warranty. Note: Make sure all control knobs are in the off position, LP tank valve is closed and tank is disconnected from regulator and removed from grill. Step 1 Using an adjustable wrench to hold the gas manifold connection secure, use a 3/4” wrench to loosen the hose connection nut. Replace existing LP hose/regulator assembly with natural gas 10’ hose assembly. Tighten both connections carefully using two wrenches. Step 2 Remove cotter pin from side burner "foot". Carefully lift side burner up and away from valve nozzle. Set aside for later use. Step 3 Open hood and remove warming rack, cooking grills and heat shields. Set aside for later use. 13 CONVERSION INSTRUCTIONS 810-8550-S, 810-8552-S & 810-8555-S Gas Manifold Nut Cooking Grills Heat Shields Cotter Pin Warming Rack 10’ Natural Gas Hose 14 Step 4 Remove screw from each burner "foot" using a screwdriver. Carefully lift each burner up and away from valve openings. Set aside for later use. Step 5 Use the gas orifice tool to remove the LP brass orifice from main burner valves through the hole on the firebox front panel. Repeat this step for all main, side and rotisserie burner valves in your grill. The side burner valve orifice is under the side shelf. Note: All orifices of the grill, except rotisserie, are double orifices type (LP gas and natural gas).You only remove the LP gas orifice tip. CAUTION: Some parts may contain sharp edges.Wear protective gloves if necessary. Step 6 Remove all the control knobs from the control panel and set aside for later use. LP Gas Orifice Gas Orifice Tool Side View Firebox Front Panel Stop Pin Stop Pin 15 Step 7 Figure 1 shows valve stem and bezel with the control knob removed.Take five large stop plates from the component card and place them over the main and side burner valve stems as illustrated (Figure 2).Take the small stop plate from the component card and place it over the rotisserie burner valve stem (Figure 3).Verify the tab and the stamped letter on the stop plates face out. Replace control knobs when finished. WARNING: We recommend and request that you do not remove the control panel in order to access the valve tips. If you choose to remove the control panel, you must replace the control panel bezels exactly as illustrated in Figure 2. Failure to replace the bezels as illustrated could lead to personal injury and/or property damage. Step 8 Carefully replace each burner, making sure burner openings slide over valve nozzles. Screw each main burner "foot" down using screwdriver and screws that were set aside in Step 4. Replace cotter pin in side burner “foot” that were set aside in Step 2. Step 9 Replace warming rack, cooking grills, heat shields and grease tray. Note: Follow directions in the leak testing section of this manual before using this grill. L S Figure 1 Figure 2 Stop Plate Cooking Grills Heat Shields Warming Rack Tab Figure 3 Stop Plate Tab Cover Bolts Retaining Nut Brass Orifice 1.32mm Existing Rotisserie LP Gas Orifice Replacement Rotisserie Natural Gas Orifice (identified by number) Rotisserie Burner 1.32mm (YELLOW) 810-8550-S, 810-8552-S & 810-8555-S ROTISSERIE BURNERS CAUTION: Only use specified natur...

Other models in this manual:
Convection Ovens - 810-8530-S (13.08 mb)
Convection Ovens - 810-7405-S (13.08 mb)
Convection Ovens - 810-8500-S (13.08 mb)
Convection Ovens - 810-8532-S (13.08 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category