Votes - 2, Average rating: 4 ( )

Manafacture: Brinkmann File size: 13.08 mb File name: Language of manual:

Remove wood chip drawer to get access to the wood chip burner. Remove one screw from the wood chip burner. Carefully lift each burner up and away from valve openings. Set aside for later use. Step 5 Using the gas orifice tool, remove the LP brass orifice from the tip of each gas valve assembly. Repeat this step for all main burner and wood chip burner valves in your grill. Note: All orifices of the grill, except rotisserie, are double orifices type (LP gas and natural gas). You only remove the LP gas orifice tip. Step 6 Remove all the control knobs from the control panel and set aside for later use. Step 7 Figure 1 shows valve stem and bezel with both screws. Place stop plate over valve stem as shown in Figure 2.Verify the tab and the stamped letter on the stop plates face out. Replace control knobs when finished. WARNING: We recommend and request that you do not remove the control panel in order to access the valve tips. If you choose to remove the control panel, you must replace the control panel bezels exactly as illustrated in Figure 2. Failure to replace the bezels as illustrated could lead to personal injury and/or property damage. L Figure 1 Figure 2 Stop Plate Gas Orifice Tool Side View LP Gas Orifice Wood Chip Drawer Fire Box Front Panel Stop Pin Tab 810-8905-S & 810-8907-S SIDE BURNERS CAUTION: Only use specified natural gas orifice for your grill. Step 8 Remove the side burner brass cap by using the small wrench to unscrew the two small screws. Step 9 Remove access panel on left side of grill for better view of gas orifice. Step 10 Use the gas orifice tool to remove LP brass orifice from the hole on the top of side burner. Step 11 Using gas orifice tool, install 1.25mm (GREEN) natural gas orifice. Be careful not to cross thread natural gas orifice. Small Wrench Brass Cap Access Panel Step 12 Replace the side burner brass cap to the burner. 1.25mm Existing Side Burner LP Gas Orifice Replacement Side Burner Natural Gas Orifice (identified by number) Side Burner 1.25mm (GREEN) Gas Orifice Tool Cover Bolts Retaining Nut Brass Orifice 1.51mm Existing Rotisserie LP Gas Orifice Replacement Rotisserie Natural Gas Orifice (identified by number) Rotisserie Burner 1.51mm (BLUE) 810-8905-S & 810-8907-S ROTISSERIE BURNERS CAUTION: Only use specified natural gas orifice for your grill. Note: It is helpful to keep the screws with the components as they are removed for ease of reassembly. Step 13 Remove rotisserie cover bolts and remove rotisserie cover to gain access to the rotisserie LP gas orifice on back side of grill. Step 14 Using an adjustable wrench to hold the gas line secure, use the open end wrench provided to loosen the gas line retaining nut. With the rotisserie gas supply line detached from the housing, use two wrenches to remove the LP brass orifice from the gas supply line. Replace the LP gas brass orifice with the proper natural gas orifice. (1.51mm BLUE) Note: Bending the hose could damage the supply line. Step 15 Reattach gas supply line to the rotisserie housing by securing with the retaining nut removed in Step 14. Note: Leave the back panel off until the end of conversion and all gas leak testing has been completed. Step 16 Re-install the rotisserie cover using the nuts and bolts that were set aside in Step 13. Step 17 Carefully replace each burner, making sure burner openings slide over valve nozzles. Screw each burner "foot" down using screwdriver and screws that were set aside in Step 4. Step 18 Replace warming rack, cooking grills, heat shields and grease trays. Note: Follow directions in the leak testing section of this manual before using this grill. 9 CAUTION: Some parts may contain sharp edges.Wear protective gloves if necessary. WARNING: Only use the specific orifice designated for your grill model. Always double check the millimeter size on the side of the orifice tip prior to installation. Use of any other orifice could lead to personal injury, property damage and void your grill warranty. Note: Make sure all control knobs are in the off position, LP tank valve is closed and tank is disconnected from regulator and removed from grill. Step 1 Pull right accessory drawer out a...

Download now

Please, enter two numbers from picture: