Rapid depletion can leave a heater unprotected causing a premature failure. As with any water heater, it is good practice to check the anode annually to see if it needs replacing. Anode Inspection/Change 1. Turn the electrical supply to the water heater "OFF". 2. Close the cold inlet supply valve. 3. Open a hot water tap supplied by the heater. (CAUTION: Water will be hot). 4. See 'Draining Tank' section to remove enough water to empty the piping system. 5. Using a 1 1/16" socket, remove anode a

Inlet Gas Pressure (inches of water) Maximum 10.5" Minimum 4" Dimensions, Inches (H x W x D) Heater (Including knobs and grill) 21 1/2 x 13 1/2 x 7 Carton 25 1/4 x 16 3/4 x 7 1/2 Weight (pounds) Shipping 19 When gas pressure is too low • pilot will not stay lit • burner will have delayed ignition • heater will not produce specified heat When gas quality is bad • pilot will not stay lit • burner will produce flames and soot • heater will backfire when lit You may feel your gas pressure is too low

Refer to page 3 of this manual. This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by state or local codes. * Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases. Save this manual for future reference. BLUE FLAME 6000 BTU/HR VENT FREE PROPANE/LP GAS HEATER SAFETY INFORMATION WAR

dealer where you bought heater for proper type heater. INSTALLING HEATER TO WALL Marking Screw Locations 1. Determine where you will locate heater. WARNING: Maintain minimum clearances shown in Figure 5. If you can, provide greater clear- INSTALLATION ITEMS Before installing heater, make sure you have the items listed below. • external regulator (supplied by installer) • piping (check local codes) • sealant (resistant to propane/LP gas) • equipment shutoff valve * • ground joint union • test gau

Ignitor cable pinched or wet 2. Ignitor electrode not connected to ignitor cable 3. Piezo ignitor nut is loose 4. Broken ignitor cable 5. Ignitor electrode broken 6. Bad piezo ignitor 7. Ignitor electrode positioned wrong 1. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry 2. Reconnect ignitor cable 3. Tighten nut holding piezo ignitor to heater cabinet. Nut is located inside heater cabinet at top 4. Replace ignitor cable 5. Replace ignitor 6. Replace piezo ignitor 7.

WARNING: HOTTER WATER INCREASES THE RISK OF SCALD 3. Depress gas control slightly and turn clock-wise to “OFF”. If knob is in “ON” position, turn clock-wise to “PILOT” then depress knob slightly and turn clock-wise to “OFF”. 4. Wait five (5) minutes to clear out any gas. If you smell gas, STOP! Follow “B” in the safety information at the head of this section. If you don’t smell gas, go to the next step. 5. Remove burner access cover located below the gas control unit. 6. Find pilot - follow smal

When away for extended periods of time such as vacation, and no freezing temperatures are expected: . 15 . 1. Shut off the oil supply at the tank. 2. Shut off the cold water supply to the heater. 3. Turn "OFF" the electrical supply to the water heater. 4. Open an upstairs hot water faucet (to relieve any pressure). When freezing temperatures are expected: NOTE: It is recommended that all water lines in the home be drained. Contact a qualified plumber for directions applicable to the heater. 1. S

Never operate the heater if it is not completely filled with water. To make sure the heater is filled, open the hot faucet of an upstairs tap, until there is a full flow of water with no air coming through the tap. Flue Pipe. Once a year, inspect the flue pipe leading from the heater to the chimney. If corrosion is evident, or discolouration at the joints can be seen, replace the flue pipes. This should be done by a qualified Oil-Burner Technician. Flue pipes must be replaced by the same size fl