Votes - 1, Average rating: 3
(
)
)
|
manual abstract
Password can be easily changed if desired. Temporary Password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries. Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes. Operation: Opener activates when 4-digit password and Enter button is pressed. If wrong numbers are accidentally pressed, correction can be made immediately. The Enter button will transmit only the last four digits. The Keypad will blink for 15 seconds after the password is transmitted. During that time the Enter button can be used to stop or reverse the door travel. 1 Model 940C Security.® Wireless Keyless Entry To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. WARNING CAUTION 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control (all three buttons are held). 4. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. 1. Press and release the .learn. button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button. 3. Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. LOCK LIGHT SETTING THE PERSONAL ENTRY PASSWORD We recommend that you program your password now, before you install the Keyless Entry. Then you can test the reception at the mounting location before you proceed further. USING THE MULTI-FUNCTION DOOR CONTROL USING THE .LEARN. BUTTON Side two contains instructions for installing the Keyless Entry, changing the personal entry password and setting a temporary password. LOCK LIGHT LOCK LIGHT ™/ NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Typical Sectional Door INSTALLATION Choose a convenient Installation location for installation. Exterior Front Wall It should be at eye 1-Piece or level, reachable by the Sectional Door shortest person who will use it, and within Keypad Door Jamb Edge sight of the door. (Optional Location for 1-Piece Door) For a one-piece door, choose the optional Door Jamb Face SECTIONAL DOOR ONLY location shown in the illustration to avoid KEYPAD MUST BE INSTALLED injury as the door WITHIN SIGHT OF THE DOOR swings up and out. Test the reception of the Keyless Entry by operating your opener from the selected location. Change the location if necessary. Remove the battery compartment cover to access the bottom mounting hole: . Insert a small phillips screw driver into the small hole at the bottom of the cover and gently pull outward to loosen. . Slide the cover down to remove. Center the keypad at eye level against the selected location. Mark 4-1/4" up the centerline from the bottom and drill a 1/8" pilot hole. Install top mounting screw, allowing 1/8" to protrude Battery Bottom mounting hole Battery Cover above surface. Position keypad on screw head and adjust for snug fit. With cover open so bottom mounting hole is visible, use a punch to mark hole. Remove keypad and drill 1/8" pilot hole. Replace keypad and complete installation with bottom screw, using care to avoid cracking plastic housing. Do not overtighten. To replace the battery cover, insert the lip at the top and snap in place. THE KEYLESS ENTRY BATTERY WARNING To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. The 9 volt battery should produce power for at least one year. Replace when the keypad illumination becomes dim. Dispose of old batteries pr...